6423 FG Gear protector for 42/44/46/48 T spur gears

€39.90*

Available

Product number: fg_6423

EAN: 3410564508350

Product information "6423 FG Gear protector for 42/44/46/48 T spur gears"

Genuine FG spare/option part.

Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth.

Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground.

Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

6732/07 FG E-clip spring steel 7 mm

Genuine FG spare/option part. Fits FG clutch bell and FG + Carson layshaft.Part is delivered in silver or black color from vendor!Content:15 pieces

€2.90*

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

6106/05 FG Snap rings 19,5mm for wheel square

Genuine FG spare/option part. Securing ring for positioning the brake disk on 11.5, 14 and 17mm square drives.Inner diameter unstretched 19.5 mm.Part is delivered in silver or black color from vendor!Contents:4 pieces

€4.60*

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

7154 FG Body mount adjustable, 1 pce.

Adjustable body mount with heigt-adjustable body support.Measures:Length 110 mmDiameter 8 mm10 mm at the baseFor all cars and body shells.

€9.95*

6052 FG Plastic gearwheel 48 teeth

Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

€17.90*

Similar products

6745 FG Shim ring 10x16x1mm - 10pcs.

Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!

€5.30*

6730/05 FG Allen Grub screw M5x5 mm, 15 Stück

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€3.40*

6730/52 FG Grub screw with safety device M5x5mm Torx, 10 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

€3.20*

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Configure now

6439 FG Alloy spur gear carrier 60 mm

Genuine FG spare/option part. For 48T - 46T spur gears.Contents:1 piece

€39.50*

7439/05 FG Alloy gear carrier 52mm special, 1 pce.

Item N° 7439/05 Alloy gear carrier 52mm special, 1 pce.Precision alloy gear carrier, exact support of the plastic gearwheels 39, 40, 41, 42 and 44 teeth. Very low height design. For 10 mm diameter shafts.Please note: competition layshaft 6041/05 is necessary for installation!

€39.50*

7439 FG Alloy gear carrier 52mm - 1pce.

Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.

€41.90*

7438 FG Alloy gear carrier 47mm - 1 pce.

Suitable for .For 10 mm diameter shafts.

€39.90*

6730/71 FG Allen Grub screw M5x6 mm

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€3.20*

y1427 HT steel spur gear on-road with 39, 40, 41 teeth

y1427 Version: y1427/41 HT steel spur gear

Fits FG and Smartech touring cars in combination with HT aluminum layshaft spur gear carrier on-road y1428. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions

€49.90*

6495 FG Fine pitch gears EVO 2020

Genuine FG spare/option part. ClutchGear shaft outerGear shaft innerDifferentialReduction ratio345823735,41345823745,49345824735,19345824745,26355823735,26355823745,33355824735,04355824745,11365823735,11365823745,18365824734,90365824744,97375823734,98375823745,04375824734,77375824744,84Contents:1 set

€279.95*

y1379 Pinion fastening set with nut for Losi 5ive-T/2.0 and Mini

This set allows for fastening the pinion to the clutch bell utilizing a full metal self locking nut when using our gas-nitrided clutch bell y0726. The screw will be fully inserted into the clutch bell from the backside using high strength thread locking compound. This setup provides a couple of significant advantages:This self locking nut does not use the usual plastic insert; therefore it is completely temperature resistant!Theres no need to wait for the thread locking compound to cure after a pinion change; the connection is safe and ready to use immediately. For safety reasons nut and spring lock washers should only be used once.No need to worry about worn-out Allen screw heads.In case the screw ever breaks at the point where it enters the pinion, it can still be removed with ordinary tools. Theres still the like new screw head inside the clutch bell ready for screw removal. Set includes:2 pieces of high strength 12.9 grade screws10 pieces of full metal self locking nuts10 pieces of spring lock washers

€5.90*

Customers also viewed

y1570 CYS S0650 large scale servo with Double sided alloy servoarm, 55 kg/0,11 sec

CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece

€69.90*

y0797 SPEED TEC EXPERT Zenoah 30,5 cm³ tuning engine

The SPEED TEC EXPERT genuine Zenoah 30,5 cm³ engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust and intake. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome ground. Crankshaft: The Zenoah 30,5 cm³ SPEED TEC Expert comes with the genuine Zenoah +2 mm stroker crank #577953101. It is adjusted, aligned and balanced. Flywheel: weight reduced and checked for runout. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC EXPERT engine, we recommend the use of a tuned pipe ( to the tuned pipes ).

€699.00*

Details