6422 FG Plastic gearwheel 44 teeth - 1pce.
€17.90
Available
Product information "6422 FG Plastic gearwheel 44 teeth - 1pce."
Diameter 69 mm
Width 15.5 mm
Tooth width 12 mm
Module: m=1,5
Login
Alternatives
Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5
Accessories / Spare parts
Hardened steel gearwheels for the gears of the 1/6 off-road models.Module: m=1,5
Customers also bought
Item N° 6432 Steel pinion 18 teeth - 1pce.For combination with 46T main spur gear.Diameter 29,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5
Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece
Nitrided hardened, highly wear-resistant.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)For use on the clutch bell of FG cars in combination with a 48t spur gear on the layshaft. Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece
Customers also viewed
44 teeth plastic main gear for the layshaft with 2-speed gear.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5
46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5
Item N° 6432/02 Steel pinion 19 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Nitrided hardened, highly wear-resistant.Not suitable for Smartech and Carson models. Suitable for FG offroad models 2WD on the clutch bell to the 42 main gear. This pinion is profile shifted and has a 1.5 module. This means that the number of teeth of the gear is changed compared to the previously known values while the diameter remains the same. The area of the involute curve that determines the tooth profile is shifted. Positively shifted gears (fewer teeth than normal) are more stable and run more smoothly; the slightly lower strength of negatively shifted gears is irrelevant. 1 piece
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece
Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!
Item N° 7431/21 Steel gearwheel hardened 21 teeth - 1pce.Suitable for 42 teeth main gear wheel.Diameter 35.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.