y0700 Double sided alloy servoarm: 9,90 EURy0700/01 Single-sided alloy servoarm: 7,90 EURy0701 Double sided split alloy servoarm: 14,90 EURy0701/01 Single-sided split alloy servoarm: 12,90 EURFor y0700, y0700/01, y0701 and y0701/01:Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVy2007 Digital large scale Brushless Servo CYS9130Nearly all Ribbe/Futaba servosMega Power servoThunder Tiger DS1015And many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarm are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
PMT tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine PMT spare/option part. The Supreme have been designed for all track conditions. Developed with latest generation components, deriving directly from the highest level of Motorsport, they are available in three hardnesses:SS "NEW": supersoft, 35 shore hardness, suitable for rear and slightly abrasive asphaltsS00 (K00): soft, 38 shore hardness, suitable for rear and slightly abrasive asphaltsM00/P1 (K01): medium, 42 shore hardness, suitable for rear / front and medium abrasive asphaltsH00/P1 (K03): hard, 45 shore hardness, suitable for front and very abrasive asphaltsOn this type of tyres a new lighter and harder rim will be used, designed to withstand 25% higher lateral forces, compared to existing ones.Moreover, even the filling mousse has been updated and can now withstand up to a temperature of 130 °, without altering its mechanical characteristics. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square drive Contents:2 pieces
Genuine HT spare/option part.Very strong a-arm, allows for camber adjustment. Features Igus bushings for the hinge pins (stock hinge pins can be re-used).Fits Smartech Monster, Carson Comanche, Attack Evo, CRT 2WD and CPT. Contents:1 piece
tt_tt1000 Connector:
TT1000/01 Universal in - Universal out
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Genuine FG spare/option part. Plastic radio plate for installation of up to 4 servos. Fits all FG street models (except Formula 1) and Leopard models.You will need FG #6118/05 for installation of any steering servo other than Hitec 805BB.Contents:1 piece
Plastic wishbone with 6mm boring suitable for the reinforced wishbone threaded rods M6.
€19.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).