y04474 HT Rear upper alloy wishbone 2WD

Rear upper a-arms, a clamping system for the turnbuckles makes lock nuts obsolete.

Genuine FG spare/option part. Rear upper alloy wishbone with droop stop.Replacement for plastic wishbone FG 6074/02.Content:2 pieces

Tuning aluminum rear suspension set for nearly all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Tourenwagen.Does not fit Formula 1, Leopard and Truggy!Assembled units in the pictures are completed with some parts which are not included. These parts will be re-used from the stock suspension when swapping in the aluminum version. You will also need two bags of 6100/04 Turnbuckle left/right M8/40mm.y2004/01 fits:FG 4WD Monster-Truck models and Monster Beetle models, Off-Road, Marder, Beetle, Porsche GT3 RSR and Race Trucks. The only difference between the sets is the length of the lower a-arms (y2004/01 = long, y2004/02 = short). The picture of the assembled set is used for both versions and shows the shorter arms.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/02 fits:FG 4WD Touring car models (except Porsche GT3 RSR).Part number:Name:y2001Aluminum rear upper a-armsy68401/01Aluminum rear lower a-arms short66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/03 fits:FG 4WD/2WD Off-Road WB535.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213/02Aluminum rear shock towery66205/06Aluminium rear diff mounts

The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURFeatures:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Replaces FG 7087/02.Fits all FG shocks, Carson 2WD and many other 1/5 and 1/6 scale models. There are replaceable bushings.Dimensions:Length overall: 27 mm, about 22 mm to to center of bushingThread for shock shaft: M4Bushing inner diameter: 4 mmContents:2 pieces

Genuine FG spare/option part.Alloy rear axle mount right Leopard 2WD/4WD.