6730/05 FG Allen Grub screw M5x5 mm, 15 Stück

Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece

Item N° 7439/05 Alloy gear carrier 52mm special, 1 pce.Precision alloy gear carrier, exact support of the plastic gearwheels 39, 40, 41, 42 and 44 teeth. Very low height design. For 10 mm diameter shafts.Please note: competition layshaft 6041/05 is necessary for installation!

Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.

Genuine FG spare/option part. ClutchGear shaft outerGear shaft innerDifferentialReduction ratio345823735,41345823745,49345824735,19345824745,26355823735,26355823745,33355824735,04355824745,11365823735,11365823745,18365824734,90365824744,97375823734,98375823745,04375824734,77375824744,84Contents:1 set

Suitable for .For 10 mm diameter shafts.

Genuine FG spare/option part. For 48T - 46T spur gears.Contents:1 piece

This carriers makes it possible to run steel spur gears on the layshaft. Pebbles heat and the high torque of monster truck applications are no longer a problem.The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of the pinion and the spur gear carrier are pointing to the outside of the car. The carrier features M8 (eight, no typo) grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution.Please note: the wide FG 48T spur gear 6048/2 does not fit this adapter, but it wouldn't be recommended for this application anyway; it's way too heavy.Content:1 piece

Alloy ring gear adaptor for FG, Smartech, Carson and many other cars. Contrary to the stock plastic adaptor the aluminum version is secured by set screws.There are three sizes available:y0048/01 - 47 mm outer diameter, fits 38 tooth ring gearsy0048/02 - 52 mm outer diameter, fits 39/40/41/42/43/44 tooth ring gears - Weight: 29 grammsy0048/03 - 60 mm outer diameter, fits 46T and 48T ring gears - Weight: 31 gramms

Genuine FG spare/option part. ClutchGear shaft outerGear shaft innerDifferentialReduction ratio345823735,41345823745,49345824735,19345824745,26355823735,26355823745,33355824735,04355824745,11365823735,11365823745,18365824734,90365824744,97375823734,98375823745,04375824734,77375824744,84Contents:1 piece

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

Contains all bearings for the specified car.Complete ball bearing set for all FG touring / offroad 2WD cars (not Formula 1) and all Carson 2WD large scale cars (offroad and touring cars).Your choice of plastic or alloy diff case.The set includes:- wheel bearing, 8 pcs., 8x22x7 mm- clutch bell bearing, 2 pcs., 10x22x6 mm- layshaft bearing, 2 pcs., 10x19x7 mm- diff bearing, 2 pcs., 12x28x8 mm for plastic diff case or 15x28x7 mm for aluminum diff case.

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

Spare part for 7348 also suitable for the Losi 5ive-T.Measures:Inner diameter: 3.2 mm Length: 400 mm