7474 FG Alloy gear plate 97 for 2WD and 4WD

€93.40*

Available

Product number: fg_7474

EAN: 3410564518601

Product information "7474 FG Alloy gear plate 97 for 2WD and 4WD"

Genuine FG spare/option part.

Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.

Bearing seats

Clutch bell: 22 x 6 mm
Layshaft: 19 x 7 mm

Content:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

7474/05 FG Spacer bushing Ø13/10 x 5 mm

Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece

€3.70*

7040/01 FG Alloy brake caliper 97

Genuine FG spare/option part. For gear plates 7039/1 oder 7474. Only for use with single brake disc on the layshaft.Contents:1 piece

€37.00*

Customers also bought

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€47.90*

15478 HPI Pull starter 1/5

Genuine HPI spare/option part. Content:1 piece

€59.90*

FG TR4 Truggy 4WD HT-Edition

Ready for an extra portion driving fun? Then try the TR4 made by FG! Agressive appearance combined with the Leopard 4 chassis results in an optimal handling and stunning top speed with lots of driving fun wich will thrill you. Equipped with a 26 cm³ two-stroke gasoline engine with installed pull-start system. The TR4 is an uncomplicated complete package with well-tired racing technology.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical information:Strong 26 cm³ gasoline engineMaintenance friendly chassisTwo differential gearsHardened driving partsCompletely ball-bearedLarge-volume aluminium dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure driving funHT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURDimensions: Length: 760 mm Width: 520 mm Height: 320 mm Wheelbase: 534 mm

€1,279.95*

Configure now

7497 FG Rear brake 97 for 1:5 and 1:6

Genuine FG spare/option part.Improved rear brake for Marder, Beetle Off-Road, Beetle On-Road and Pajero as well as EcoLine, not for Formula 1. Big epoxy brake disk (diameter 52 mm) for more brake power. Gear carrier is not included in the set. Only in connection with 7039/01or 7474.Contents:1 set

€52.50*

Details

7316 FG Clutch blocks for Zenoah

Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€27.90*

y7343/08 Champion Spark plug for Zenoah/CY and other

Genuine Champion spare/option part.The Champion spark plug means higher speed range, longer time of exposure andimproved starting function. Thread size M10 x 1 fits CY / Fuelie / PT / Zenoah G230/240/260/270/290 and otherSerienkerze vom Zenoah G230/240/260/270.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:1 piece

€9.90*

Details

Customers also viewed

7040/01 FG Alloy brake caliper 97

Genuine FG spare/option part. For gear plates 7039/1 oder 7474. Only for use with single brake disc on the layshaft.Contents:1 piece

€37.00*

7474/05 FG Spacer bushing Ø13/10 x 5 mm

Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece

€3.70*

y1135 Alloy gear plate for Carson / Smartech C6

Genuine HT spare/option part.Fits all Carson / Smartech 2WD buggy and monster cars like UNOMonster Truck AttackSuper AttackAttack EvoComancheCRT, CPTGas Blaster...The brake cam bushings are replaceable.Contents:1 piece

€69.90*

7497/01 FG Rear brake 2WD/4WD

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

€53.90*

7497 FG Rear brake 97 for 1:5 and 1:6

Genuine FG spare/option part.Improved rear brake for Marder, Beetle Off-Road, Beetle On-Road and Pajero as well as EcoLine, not for Formula 1. Big epoxy brake disk (diameter 52 mm) for more brake power. Gear carrier is not included in the set. Only in connection with 7039/01or 7474.Contents:1 set

€52.50*

Details

65154 Multiplex Servo Rhino pro SHV digi 4 Angebot

The RHINO pro SHV digi 4 servo is a 29 mm digital servo designed for use in large-scale models. The new pro SHV servo is faster, more powerful, and more durable than the proven RHINO digi 4, of which thousands are now in use. More performance, with higher torque and faster transit speed, and more durable with a new triple-ballraced heavy-duty steel gear set. The operating voltage range has been expanded to 7.4 V, allowing the servo to be operated directly with up to two-cell LiPo batteries.Large 1 : 5 scale model cars make very exacting demands on the servos, and for many years the RHINO servo has set the standard with its extremely robust, outsize metal gearbox and 8 mm output shaft for the output device. An integral aluminium heat-sink cools the motor and electronics very effectively. Servo case gaskets make the unit dust-proof and splash-proof. The enormous power and robust nature of this servo also make it an excellent choice for large models generally, such as F3A - XXL large-scale model aircraft, as well as for non-standard applications.Adapter FG # 6118/02 is required for installation into a FG/Smartech car.High-voltage (HV) servosHV servos have a broad operating voltage range of 5 - 7.4 V, i.e. they can be operated directly with two-cell Lithium-based rechargeable batteries (e.g. LiPo, LiFe, LiIo). The outstanding features of LiXX batteries compared with NiXX types are their higher energy density and lower self-discharge rate, and for these reasons they are increasingly used as power supplies in model RC systems. The higher voltage of LiXX batteries means that the current drawn by an HV servo is lower for a given output power than that of conventional servos, which are generally designed for a nominal voltage of 4.8 - 6 V. When used with 2S LiXX batteries, these older servos must therefore be operated with a separate voltage reducer. This reduces the overall efficiency of the system, leads to unnecessary dissipated power, requires additional electronic complexity and more connectors ( higher costs, greater failure risk, higher weight). Modern receivers (e.g. M-LINK) are designed for voltages up to 9 V, i.e. with HV there is no longer any reason not to use the modern, superior LiXX battery technology.The following servo parameters can be adjusted using the MULTImate test and programming unit # 8 2094:Direction of servo rotationServo transit speedServo travel, left / right (max. 2 x 90°)Servo centreServo deadbandFail-safe (On with servo Fail-Safe position / Off)Reset to factory default settingsSpecificationDimensions (L x W x H):Weight::Gearbox:Ballraces:Multi-finger wiper pot:Torque @ 6 V / 7f.4 V*:Holding power @ 6 V / 7.4 V*:Transit speed for 40°@ 6 V / 7.4 V*: 59 x 29 x 55 mm172 gSteel3yes (with indirect drive)230 / 270 Ncm280 / 320 Ncm** 0,10 / 0,08 sec.* 5-cell NiXX / 2S LiPo operation. Values measured at stabilised 6.0 V / 7.4 V.** Holding power at angular error

€119.90*

Details

1039 FG Alloy gear plate Evo 04 - 08

Genuine FG spare/option part.Only suitable for alloy gear flange-engine mount 1040/05.See below for layshaft 10x19x7 mm and clutch bell 10x22x6 mm bearings.Content:1 pieces

€49.95*