y0688 HT RTR set with 2.4 GHz remote control for all FG and Carson 1:6 scale models

Genuine Carson spare/option part. The Reflex Wheel Pro III is the innovative 2-channel entry-level RC system from Carson-Model Sport. The steering angle and the servo travel on the throttle are adjustable (Dual Rate). This allows each model to be controlled very precisely and tuned to the road. In addition, the throttle can be limited for beginners and children. The chrome steering wheel with cellular rubber surface allows precise control and can be tilted individually forwards and backwards. The automatic stop function (low-voltage protection) integrated in the receiver is the life guard for your combustion engine model. This remote control system is ideal for all areas of RC-Car sport.Absolutely ingenious yet simple is the binding procedure:1. Switch the receiver on2. Press the setup key3. Switch on the transmitter - READY!Technical details: Operating voltage transmitter 4.8 to 6 V Operation possible with Li-Ion battery or 4x AA NiMh cells 2.4 GHz FHSS system (frequency hopping spread spectrum) Two infinitely variable, fully proportional channels Servo reverse for both channels (reverse direction) Trim function for throttle and steering Dual Rate for both channels (servo travel limit) Power supply of the BEC receiver from a battery with 4.8 - 7.2V possible Integrated fail-safe (programmable) Uni connector system for Futaba and Graupner-JR Charging socket (positive center pole) Battery status indication by means of LEDContents:1 x 2-channel transmitter 2.4 GHzBEC Mini receiver

The T10PXR is a 10-channel 2.4GHz computer radio control system with F-4G,T-FHSS SR / T-FHSS / S-FHSS and MiniZ modulation modes. The transmitter convinces with new design, new keypad and high quality carbon elements. New additions are some new buttons, 2- and 3-position switches and a rocker switch at the base of the transmitter.The Futaba T10PX comes with many new features that make the new RC-car radio flagship a very flexible transmitter.With 10 channels and many configuration options, the possible uses go far beyond those of a conventional car radio.From racer and drifter to crawler and boat to complex function models, everything is possible.Overview of the modulation types: F-4G, 10 channels / telemetry T-FHSS-SR, 4 channels T-FHSS, 4 channels / telemetry li> S-FHSS, 7 channels The new F-4G transmission protocol has been further improved compared to T-FHSS SR. Latency has been significantly reduced again and the range extended. At the same time, the receivers have become smaller.The optical center of the T10PX is the backlit 4.3 inch TFT color touch display with brilliant colors and high sharpness. Even in direct sunlight, all values on the display can be read excellently. The graphic user interface with the well-known easy to use Futaba menu structure, ensures easy operation. Navigation is intuitive via the screen and the additional buttons on the top of the transmitter.TELEMETRYSynchronized, bi-directional communication between transmitter and receiver with high telemetry data rate (up to 9 times per second), without loss of control channel response. Maximum of 31 telemetry sensors, alarm tone setting and output via beeper, vibration alert or voice output via internal speaker or optional headphones/active speaker. Telemetry data recording on SD card (SDHC) Telemetry data analysis via spreadsheet programs or LogView software Real-time display of telemetry data on integrated display Receiver signal strength indicator for monitoring the range Receiver undervoltage warning system for monitoring of the receiver battery Connection of up to 31 sensors to the S.BUS2 input S.BUS-TECHNOLOGY Connection option for S.BUS2 sensors All S.BUS servos can also be connected to normal servo outputs of the receiver Digital BUS technology for model sports Allows ideal placement of all components with efficient wire routing Future-proof, digital technology for all future Futaba components Features: Color LCD Touch Screen 4.3 Inch F4G System & Telemetry S-FHSS & T-FHSS Super Response (SR) Mode MiniZ S-FHSS 10 channels 40 models memory additional 3- and 2-step switches Brake mixer for large scale cars 4-wheel steering mixer Dual ESC mixer Mixer for track drives CPS LED mixer Gyro adjustment via T10PX microSD Slot (Data Log / Update) USB port Content of delivery Transmitter T10PX Receiver 404SBS Instruction manual DE/UK Accessories

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

The 2WD-465 Sportsline electric model is based on a short chassis (465 mm wheelbase) with double wishbones Rear and front axles built. The vehicle is factory equipped with the 2-damper front axle.E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Sportsline models are equipped with a powerful brushless engine and a Brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.In the unpainted version Version does not include a decal sheet!Features:The front axle of the GT2 was widened to 384 mm. The rear axle is 395 mm wide.Chassis short 465 with double wishbones on the rear and front axle completely assembled, ball bearings, differential gear, oil pressure shock absorber, multi-part unpainted polycarbonate body (item no. 05160L), white spoke rims, tires and tire inserts.T2M standard equipment brushless motor and ESC, 6S - 150A controller up to 3-6S  - brushless motor 6S You can order a motor/ESC combination with 8S for an additional charge.- ESC 200A, 3-8S LiPo, BEC 8A - Brushless Motor 8S The model is also available in our shop selection including complete RTR equipment! RTR features RTR = Ready to Run. The RTR version is delivered ready to drive and with the 2.4 GHz remote control installed.Decor set: selectable (included in the painted version)LiPo batteries and the appropriate charger are required for all versions of the electric models. We recommend using LiPo batteries with a maximum length of 150mm and a width of 50mm to ensure trouble-free installation. The model is supplied with an EC8 connector system.

Genuine FG spare/option part.Contents:1 set