y0356 Circle cutter, 1 pce.

Steel ball joint 4 mm r/h, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One x r/h thread

The Lightscale Camber Gauge is a black anodised alloy block that features 8  different angled planes in 0.5° steps from 0.5° to 4° on different surfaces.
The gauge is to be layed down beside a tyre for negative camber angles and any 90° part is put on one of the planes an pulled towards the tyre. Doing so you can easily check the camber of your tyres. To check positive camber, just turn around the gauge.
Turning the gauge upside down will make it a 10mm high block to support you measuring the droop of any 1/5, 1/6 and 1/10 scale Electric or nitro car. Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.

We essentially simplyfied the inserting of the differential bevel gear wheels with the mounting tool. Through the exact positioning of the bevel gear wheels it is guaranteed that the differential bevel wheel axle and the differential driving axle are in true alignment from the beginning.

Genuine FG spare/option part. The body set contents the main part, front body and the rear wing. The body is clear.Required body mounts:Mount front: FG 7020/06 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mmContents:1 piecePainting tips:

Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!