y0668 Alloy engine mount big for 1:6 2WD Zenoah alloy

€64.90*

Available

Product number: y0668

EAN: 4058575033332

Product information "y0668 Alloy engine mount big for 1:6 2WD Zenoah alloy"

Genuine HT spare/option part.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

y6479 HT rear alloy upright

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€47.90*

6431/01 FG Steel pinion 16 teeth, wide - 1pce.

Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€33.90*

6047/01 FG Steel pinion 15 teeth wide, 4WD

Genuine FG spare/option part. True running steel pinion for minimized wear. Application: All FG cars except Formula 1.Dimensions:Diameter: 26,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€31.50*

7432/25 FG Steel gearwheel hardened 25 teeth

Suitable for 39, 40 and 41 teeth main gear wheel.Measures:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Content:1 piece

€34.50*

6920/14 FG Countersunk screw with Torx M4x14 mm, 10 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

€5.70*

Similar products

y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars

Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!

€99.90* €124.80* (19.95% saved)

y1149 Alloy engine mount small + large for FG Off-Road + Monster models 2WD CY/Zenoah

Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.

€95.90* €124.80* (23.16% saved)

y6485/01 Alloy engine mount small for 1:6/CY / Zenoah alloy, 1 pce.

Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270/290 engine.

€33.50*

67238 FG Alloy gear flange engine mount Leopard 2WD/4WD

Genuine FG spare/option part.Spare part for the Leopard 2010 2WD/4WD verison.Contents:1 piece

€169.95*

66215, FG Alloy engine mount large 4WD, 1pce.

For FG 1/6 4WD competition cars only.Not suitable for conversion of an FG Sportline 4WD models since several small parts required for the swap are not included. As an alternative use item no. y0497.Suitable ball bearing for the layshaft: 6036/05 FG bearing set 10x19x7 with grease filling - 2 pcs

€84.90*

6486 FG Alloy engine mount big for 1:6 2WD Zenoah alloy - 1pce.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

€69.95*

6485/01 FG Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.

Item N° 6485/01 Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270 engine.

€43.90*

67338 FG Aluminum gear flange engine mount, gear brake

Replacement part for: 67360 Conversion kit for gear brake LeopardContents:1 piece

€152.95*

6264/01 Small aluminum engine mount for FG Leopard 1

This part fits FG Leopard 1/ Leopard Race (built until approx. 2007) with CY / Zenoah G230/240/260/270/290 engine only! Replacement for plastic version FG 6264.Contents:1 piece

€29.90*

y0497 Alloy engine mount large for all FG 4WD Models

Large alloy engine mount for all FG 4WD cars.Contrary to the FG pack this one includes the complete hardware for installation in Sportsline cars as well!

€69.90*

Customers also viewed

6486 FG Alloy engine mount big for 1:6 2WD Zenoah alloy - 1pce.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

€69.95*

y1149 Alloy engine mount small + large for FG Off-Road + Monster models 2WD CY/Zenoah

Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.

€95.90* €124.80* (23.16% saved)

y0145 Alloy engine mount, small, for Carson C5 / R5 / Smartech Ranger / Reely onroad cars, 1 pce.

CNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant.They come with all necessary hardware included.

€39.90*

y1135 Alloy gear plate for Carson / Smartech C6

Genuine HT spare/option part.Fits all Carson / Smartech 2WD buggy and monster cars like UNOMonster Truck AttackSuper AttackAttack EvoComancheCRT, CPTGas Blaster...The brake cam bushings are replaceable.Contents:1 piece

€69.90*

y0580 Mammoth Supergrip for 1/6 and 1/5 offroad cars glued

If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price 85,80 EUR 105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.90*

7486 FG Alloy engine mount big 1:5 for Zenoah/Solo

Genuine FG spare/option part. CNC-cut alloy engine mount for all FG 1:5 and 1:6 Truck models with horizontal engine ahead as Zenoah ZG22, G230RC, G260RC, FG CY23 and CY26.Bearing seat 19 x 7 mm.Contents:1 piece

€64.95*

y0654 Alloy engine mount big 1:5 2WD for FG Sportsline Zenoah

CNC-cut alloy engine mount for all FG 1:5 and 1:6 Truck models with horizontal engine ahead as Zenoah ZG22, G230RC, G260RC, FG CY23 and CY26.Bearing seat 19 x 7 mm2WD FG 1/5 Sportsline cars do not use a small engine mount. For this application the stock aluminum plate # 7398 is used for engine installation.

€69.90*