6047/01 FG Steel pinion 15 teeth wide, 4WD

€31.50*

Available

Product number: fg_6047_01

EAN: 3410564532645

Product information "6047/01 FG Steel pinion 15 teeth wide, 4WD"

Genuine FG spare/option part.

True running steel pinion for minimized wear. Application: All FG cars except Formula 1.

Dimensions:

Diameter: 26,7 mm
Bore: 10 mm
Total width: 18 mm
Tooth width: 11.5 mm
Module: m=1,5

Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

y6479 HT rear alloy upright

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

6431/01 FG Steel pinion 16 teeth, wide - 1pce.

Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€33.90*

7432/25 FG Steel gearwheel hardened 25 teeth

Suitable for 39, 40 and 41 teeth main gear wheel.Measures:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Content:1 piece

€34.50*

6920/14 FG Countersunk screw with Torx M4x14 mm, 10 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

€5.70*

Similar products

6038 FG Engine mount washers for M4 and M4 screws

Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces

€6.50*

6029/08 FG Ball-and-socket joint for M8

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M8 thread rods. Replacement for the plastic ball-and-socket joints 6029/01.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

€12.90*

6051 FG Dampening rubber

Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces

€9.50*

6041 FG Steel layshaft 10 mm

Genuine FG spare/option part. For all FG models except Formula 1.Dimensions:Length: 103 mmDiameter: 10 mmImportant:When installed in a Carson / Smartech model the brake hub is fastened with a screw stomach.Content:1 piece

€23.90*

Details

6050 FG Plastic gear carrier 60 mm

Genuine FG spare/option part. Plastic version, 60 mm diameter. For 48T - 46T spur gears.Also available in aluminum .Content:1 piece

€13.50*

6029/07 FG Ball-and-socket joint for M6

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M6 thread rods. Replacement for the plastic ball-and-socket joints 6029.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

€12.90*

6025/02 FG servo saver spring

Genuine FG spare/option part. Dimensions:Wire diameter: 3 mmInner diameter of eyelet: 12.3 mmContents:1 piece

€7.90*

6028/01 FG Track rod left/right 74mm for 1:6 models

Genuine FG spare/option part. Fits all FG 1/6 off road cars, alloy version.Length of threaded section approx. 17 mm.Contents:2 pieces

€13.90*

6045/01 FG Brake shaft 97 with brake lever

Genuine FG spare/option part. For single disc brake only.Measures:Length: 91 mmDiameter: 6 mmThread: M3Contents:1 set

€14.50*

6037/01 FG Steel mounting plate - 2pcs.

Item N° 6037/01 Steel mounting plate - 2pcs.Connects the large engine mount to the engine flange on all FG cars except evo 04 / evo 07 / competition 07Bulk:large extent plate:length: 35 mmwidth: 10 mmheight: 2 mmsmall extent plate:length: 25 mmwidth: 10 mmheight: 2 mm

€8.90*

6027 FG Ball-and-socket joint 6mm with ball

Genuine FG spare/option part. Plastic ball joint Fits all FG cars.Dimensions:Thread size: M4Länge: 20 mmBall bore: 3 mmHeight: 8 mmContents:6 pieces

€15.50*

6052 FG Plastic gearwheel 48 teeth

Genuine FG spare/option part. Stock spur gear for all FG monster cars.Suitable for spur gear carriers: 6050 (plastic) 6439 (aluminum)Dimensions:Diameter: 75 mmWidth: 15.5 mmTooth width: 12 mmModule: m=1,5 Contents:1 piece

€17.90*

Customers also viewed

6047 FG Steel pinion small 15 teeth

Genuine FG spare/option part. True running steel pinion for minimized wear. Suitable for all FG cars.Dimensions:Diameter: 26,7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Contents:1 piece

€31.50*

7438 FG Alloy gear carrier 47mm - 1 pce.

Suitable for .For 10 mm diameter shafts.

€41.30*

y0267 HT-Steel pinion, fine pitch, 23 Teeth

Genuine HT spare/option part.Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance. Only for use with the fine pitch differential ring gear! Module: m=1.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]

€28.90*

FG main catalog 2025 only as download

FG Catalog 2025 only as download. Link : https://drive.google.com/file/d/1HImXhA0lNk3j4V1aV_zAJQLvaNoPSG2d/view?usp=sharing

€0.00*

6423 FG Gear protector for 42/44/46/48 T spur gears

Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece

€43.90*