y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars
Product number:
y2005
EAN:
4058575039525
Product information "y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars"
Tuning aluminum engine mount set for all FG 4WD Sportsline cars:
Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.
Inhalt:
Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.
Inhalt:
- Aluminum large engine / layshaft mount
- Aluminum small engine mount
- All necessary screws are included!
Login
Accessories / Spare parts
Large alloy engine mount for all FG 4WD cars.Contrary to the FG pack this one includes the complete hardware for installation in Sportsline cars as well!
Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270/290 engine.
Customers also bought
Springs with different hardnesses for servo saver item-no. FG 68420.Red = soft, for budget-priced RTR servos with plastic gear.Blue = medium, for high-quality competition servos.Content:1 piece
y0732_01 Clutch shoes:
With special wear resistant organic pad
Regular price Big Scale Clutch: 109,90 EUR Nitriding hardened clutch bell: 40,50 EUR complete price:.......................150,40 EURAdjustable 3-shoe clutch for:Zenoah / Losi / Chung Yang / HPI - Fuelie / Smartech PT and many other engines.The Big Scale-Race clutch is equipped with 1.4 mm springs. This version is particularly suitable for on-road use. (not for Formular 1)The GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application. Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Handling instructions for three-shoe clutches y0730 GPM Big Scale Cross and y0731 GPM Big Scale RaceInstallation:The GPM Big Scale clutch will be bolted to the crankshaft using the supplied CSH-screw.It should be noted that the use of thread locking compound on that screw is neither necessary nor recommended!Removal:Remove the CSH-screw with a 4mm Allen wrench; then insert a suitable M8 bolt and remove the clutch from the crankcase cone by tightening that bolt. Hole for adjustment:For clutch adjustment without removing the clutch bell a 4 4.5 mm hole must be drilled into the clutch bell for access to the adjustment screw. Placement of the hole depends on clutch bell dimensions and car; so you have to make your own measurements for the placement of the hole.It is important that the drilled hole is thoroughly deburred (at least on the inside of the clutch bell) to prevent excessive clutch pad wear. Breaking in:A new clutch or shoes fitted with new pad should always be broken in. Therefore the clutch engagement speed should not be too high for the first tank of fuel. This gives the lining the possibility to adjust to the clutch bell without glazing. The only difference between two clutches is the clutch spring rate, which provides the optimal range for clutch engagement depending on the application. The three available versions of clutch springs provide adjustability within the following RPM ranges:Silver springs 1.3 mm y0730/05 (standard on Big Scale Cross): 5,000 9,500 RPMGold springs y0730/06 1.4 mm (standard on Big Scale Race): 6,500-11,500 rpm Adjustment:Adjustment of the clutch engagement speed is done by one single screw using a Handling instructions for three-shoe clutches y0730 GPM Big Scale Cross and y0731 GPM Big Scale RaceInstallation:The GPM Big Scale clutch will be bolted to the crankshaft using the supplied CSH-screw.It should be noted that the use of thread locking compound on that screw is neither necessary nor recommended!Removal:Remove the CSH-screw with a 4mm Allen wrench; then insert a suitable M8 bolt and remove the clutch from the crankcase cone by tightening that bolt. Hole for adjustment:For clutch adjustment without removing the clutch bell a 4 4.5 mm hole must be drilled into the clutch bell for access to the adjustment screw. Placement of the hole depends on clutch bell dimensions and car; so you have to make your own measurements for the placement of the hole.It is important that the drilled hole is thoroughly deburred (at least on the inside of the clutch bell) to prevent excessive clutch pad wear. Breaking in:A new clutch or shoes fitted with new pad should always be broken in. Therefore the clutch engagement speed should not be too high for the first tank of fuel. This gives the lining the possibility to adjust to the clutch bell without glazing. The only difference between two clutches is the clutch spring rate, which provides the optimal range for clutch engagement depending on the application. The three available versions of clutch springs provide adjustability within the following RPM ranges:Silver springs 1.3 mm y0730/05 (standard on Big Scale Cross): 5,000 9,500 RPMGold springs y0730/06 1.4 mm (standard on Big Scale Race): 6,500-11,500 rpm Adjustment:Adjustment of the clutch engagement speed is done by one single screw using a 2.5 mm Allen wrench. Turning the screw in increases the stall speed, backing it out will lower the stall speed. The adjusting screw is thread locked to keep the setting. Should you realize that the screw can be turned too easily please re-apply medium strength thread locking compound.Finding the best clutch engagement speed:The best clutch engagement speed should be found while driving on the track, it depends on engine characteristic, track layout, track surface and driving style.It is recommended to start with the lowest setting (which means the set screw just touching the adjustment cam) and gradually turning the adjusting screw in while doing test runs after every adjustment.If you feel that you have exceeded your best engagement speed (clutch will slip too much), back the screw out for a little bit to avoid excessive wear or glazing of the pads.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!
FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218
Genuine FG spare/option part. This conversion kit is suitable for the newer chassis of 2WD and 4WD touring and sportscars and Buggy/Monster models with 500mm - 535mm wheelbase. Suitable for the electric engines from FG Modellsport, Leopard BL engines and Castle Creation. The conversion kit includes gear and engine mount, fixing parts for cruise control and LiPo batteries. Cruise control, BL engine and LiPo batteries are not included. During the conversion several fixing holes have to be applied to the chassis. Gear transmission has to be changed accordingly to the use of the electric engine.For easy mounting we recommend LiPo batteries with a max. length of 150 mm and 50 mm width.The conversion kits include all mechanical parts (except electric engine with speed control, Lipo batteries) to convert your FG model scale 1:5 and 1:6 to an electric powered system.Contents:1 set
lager_0003 Size:
y19611 For wheel bearing, 2 pieces
Genuine HT spare/option part. Dimensions:Alloy differentials 15 x 28 x 7 mmPlastic differentials 12 x 28 x 8 mmClutch bell(except standard Formula 1) 10 x 22 x 6 mmLayshaft 10 x 19 x 7 mm Wheel bearing 8 x 22 x 7 mmContents:1 pair / 2 pieces
Similar products
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218
federn_dirt_m Version:
y0323/05 - M15, blue
Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces
Genuine HT spare/option part.Alloy a-arm front upper for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster-/ Stadium- Modelle 4WD RTR, 4WD Porsche and Mini. Replacement for FG item No.: 66266Contents:1 piece
Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.
federn_dirt_m0 Version:
y0324/05 - M05, blue
Genuine HT spare/option part. Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. All springs have an inner diameter of 21 mm.Available in several versions.For the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, blueContent:2 pieces
Alternative: y2002 Alloy a-arm, front upper FG 4WD - Fits FG Leopard 4WD und Sportsline onroad 4WD with 510mm wheelbase.Does not fit FG Leopard 2WD und Sportsline onroad 4WD with 530mm wheelbase.
Genuine FG spare/option part. Set contents front lower wishbones, rose joints, screws.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR, 4WD Porsche, 4WD Porsche and Mini.Contents:2 pieces
Customers also viewed
Dimensions same as FG 66237.Very high rupture strength and tearing resistance as well as reduced wear make this belt the perfect choicefor race applications where maximum reliability is a must.Fits cars with 490 and 510 mm wheelbase only. Does not fit WB535 cars! For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.
Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.
With DMC/EFRA homologation number #10-2014 as required for 1/5 races!Here we present the new muffler Tornado Turbo by M. Mielke. (Currently this is at the DMC for homologation.) This is a further stage of the 2013 silencer. Again It is a lightweight muffler made from 0.8 mm thick steel sheet. The design has greatly changed and the complete silencer moves more towards the vehicles center, which ensures benefits for the cars overall set-up. The performance was further improved. Distance from the rear tires (heat generation) has been increased as well.
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
%
Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.
y2003 Model:
y2003/01 - FG 4WD Monster-Truck models, Beetle+ 40EUR
Tuning front suspension set for all FG 4WD Sportsline cars: Monstertruck; Baja; Marder; Beetle; touring cars:Not fit Formular 1, Leopard and Truggy!y2003/01 fits:FG 4WD Monster-Truck models, Beetle.Part number:Name:y68412Aluminum front lower a-armsy2000Alu Querlenker Front unteny68413Aluminum front uprightsy0563Aluminum shock tower Monster-Truck/Beetley1036Rose joint for alloy wishboney2003/02 fits: FG 4WD Baja Buggy.Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishboney0579Alloy roll cage brackety2003/03 fits:FG 4WD Marder and FG touring cars with 510 mm wheelbase: Mini Cooper and Porsche GT3 RSR. When installing in a Porsche GT3 RSR or Mini Cooper 4WD with 510 mm wheelbase, the steering travel limiter must be installed into the first threaded hole of the knuckle arm and not at the standard location on the knuckle as in off-road cars!Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishbone
Variants from €469.90*
The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Performance Kit from the FW01 is particularly intended for "racer" and differs from the Chassis Kit model by the Performance Kit. Here the list of parts are not including:DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlPerformance Kit :engine brace left and rightfront stabilizer bar 2.75 mm titanium ready for installationrear stabilizer bar 1.75 mm titanium ready for installationthe two 80 gram front weightsthe two smaller 80 gram center weightsWith the Performance Kit the vehicle is quasi equipped as used at races!Stock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us! The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01. The following components are not included in the Performance Kit not and can be selected individually through the choice of options: engine, clutch, exhaust and airbox, differential gear, body shell and wheels. Not included are all relevant components for remote control! included in the kit:clutch bellbell pinionshaft and screw for clutch installationdifferential spur gearnot included:differentialbody shellairboxrear wingengineelectronicstiresclutch We are currently waiting for the latest version of the Mecatech FW01.