16 products found for "y1423"
rc-car-online - Home
Genuine Losi spare/option part. Dimensions:Outside diameter: 21,5 mminside diameter: 17,5 mmThickness: 2 mmOrifice: 4 mm Content:10 pieces
Genuine HT spare/option part. Spare part for engine quick mount y1421.
Genuine HT spare/option part. Protects stabilizer ball and stabilizer socket against dirt and prevents a clamping as well as a stiffness of the ball stabilizer. Suitable for the ball stabilizer of front and rear axle of Competition 07, Evo 04, Evo 07, Evo 08 and for Evo 2020..Dimensions:Inner diameters: 5 mm/15 mmLength: 52 mmContent:2 piece
%
Genuine HT spare/option part. The spool replaces the center differential and keeps the speed of both output shafts the same. As a result, especially the acceleration of the vehicle is significantly increased.The spool is nicely made of high-quality burnished steel and very strong. Its total length is the same as a normal differential housing with gasket. The gasket is no longer used with the spool. The driving pin of the front output shaft is secured by an O-ring. The screws for the connection with the spur gear are secured with nylock nuts. This eliminates the need for waiting for the curing of a thread locking compound and makes the removal of screws with damaged head much less critical.The spool would physically fit front and rear applications as well; however, its use here makes no sense to driving dynamics.Scope of delivery:Spool2 x Driving pin 4 x 20 mmO-ring4 x Steel nylock nut M4
Extremely flexible 6-piece body shell for Losi 5ive-T, with complete installation hardware.Made of thermoplastic elastomer (TPE), an extremely strong plastic which combines thermoplastic and elastomeric properties! Color
black (the decals pictured are not included!). The elastoplastic body set fits the stock Losi 5ive-T roll cage precisely and is almost "unbreakable"! Due to the special surface properties of TPE (elasto plastics), elasto decal sets are strongly recommended for TPE body shells.Of course, the extreme deformability of the elastoplastic body shell, compared to the stock version, is a huge advantage.And there's more with the elastoplastic body shell:Better dirt protection for the 5ive-T through partially closed wheel wells front and rear.Front and rear fenders with large cut-outs prevent contact with the tires.Integrated window nets allow for improved airflow and better engine cooling.The textured surface of the elastoplastic body shell is largely soil-resisting.Please note: This feature also makes the use of highly specialised adhesives for any kind of decals unavoidable if you want them to stay. All decals shown in the pictures for presentation are of the standard version!Even though the elastoplastic body shell is much tougher than the stock Losi 5ive-T body, the weight increase only very moderate from 902 grams to 971 grams. The body shell is a 6-piece design for best flexibility possible.Contents:1 x hood/front fender2 x side panels1 x roof2 x rear fenders1 x complete installation hardware
Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The OVER LANDER MadMax are designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the OVER LANDER is the right choice! It can even be used on partially paved tracks! Dimensions:Outer diameter: 170 mmTyre width front: 60 mmTyre width rear: 80 mmContents:4 pieces / 2 pairs Some off-road tires knowledge can be found here!
Genuine HT spare/option part.50 mm wide, extra strong duct tape, i.e. for repair of cracks in body shells or for preventative taping of RC car body shells.Content:1 piece / 50 meters
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
y1423 Version:
y1423/02 for Zenoah G320
Genuine HT spare/option part. For fitment on additional engines or as a spare part for engine quick mount y1421. The engine flange is available in two versions:y1423/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1423/02 for Zenoah G320 - For installation of a Zenoah G320 in a FG Evo (Model range from 2004 till 2014). Fits the standard quick mount.When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1423/01 does not fit in combination with Zenoah OEM clutch!
y1483 Version:
y1483/01 WT-1048 Racing carburetor
Genuine Walbro spare/option part.Popular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.Contents:1 piece
To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.
y1428 Version:
y1428/01 Suitable for FG and Smartech touring cars
Fits FG and Smartech touring cars in combination with HT steel spur gear on-road y1427. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The carrier is available in two versions:y1426/01 Suitable for FG and Smartech touring cars (not for EVO 2020)y1426/02 for FG touring cars EVO 2020
y1421 Versiown:
y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³
Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!
y1427 Version:
y1427/39 HT steel spur gear
Fits FG and Smartech touring cars in combination with HT aluminum layshaft spur gear carrier on-road y1428. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions
Offerset:1 Pair MadMax Cross Bond front tires 170x60 mm1 Pair MadMax Cross Bond rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01CROSS BOND 170 x 80 mm and 170 x 60 mm tires with black MadMax Extreme 20 bolt-beadlock rims with 24 mm hex drive and reinforced beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
y1323 Version:
y1323/02one pair for 80 mm tire width+ 3EUR
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well. Applications:for 60 mm tire width: # y1323/01for 80 mm tire width: # y1323/02
Variants from €19.90*