y1007 CFH Diamant M50 gas torch
€39.90
Available
Product information "y1007 CFH Diamant M50 gas torch"
Powerfull high quality soldering torch with piezo igniter, runs on standard lighter gas. Great for removing bolts that have been installed using thread locking compound. Removable safety base for convenient hands-free operation., adjustable flame
Technical data:
- Flame temperature: approx. 1.300 °C
- Operating temperature: approx. 650 °C
- Tank capacity: approx. 26 g Butane
- Consumption: approx. 20 g/h
- Flame adjustement: from 12 mm to 32 mm
- Ignition system: piezo ignition (like electronic lighters)
Please note: due to shipment regulations the torch is not filled with gas when delivered!
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram
Content: 20 Gramm (€395.00 / 1000 Gramm)
Customers also bought
Genuine Mecatech spare/option part for the FW01.Content:4 pieces
Genuine Mecatech spare/option part for the FW01.Content:4 pieces
Genuine Mecatech spare/option part for the FW01.4pcs 1mm4pcs 2mm2pcs 4mmContent:10 pieces
Complete ball bearing set for the Mecatech FW01, sealed on both sides.
Genuine Mecatech spare/option part for the FW01.Content:4 pieces
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
Genuine Mecatech spare/option part for the FW01.Content:8 pieces
Customers also viewed
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.