y0668 Alloy engine mount big for 1:6 2WD Zenoah alloy

€64.90*

Available

Product number: y0668

EAN: 4058575033332

Product information "y0668 Alloy engine mount big for 1:6 2WD Zenoah alloy"

Genuine HT spare/option part.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

7474 FG Alloy gear plate 97 for 2WD and 4WD

Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece

€93.40*

y6479 HT rear alloy upright

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

32430 Countersunk screw TPF 4x8mm - 5pcs.

Part is delivered in silver or black color from vendor!

€2.20*

Details

6047/01 FG Steel pinion 15 teeth wide, 4WD

Genuine FG spare/option part. True running steel pinion for minimized wear. Application: All FG cars except Formula 1.Dimensions:Diameter: 26,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€31.50*

Similar products

y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars

Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!

€99.90* €124.80* (19.95% saved)

y1149 Alloy engine mount small + large for FG Off-Road + Monster models 2WD CY/Zenoah

Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.

€95.90* €124.80* (23.16% saved)

y6485/01 Alloy engine mount small for 1:6/CY / Zenoah alloy, 1 pce.

Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270/290 engine.

€33.50*

6485/01 FG Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.

Item N° 6485/01 Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270 engine.

€43.90*

67238 FG Alloy gear flange engine mount Leopard 2WD/4WD

Genuine FG spare/option part.Spare part for the Leopard 2010 2WD/4WD verison.Contents:1 piece

€169.95*

66215, FG Alloy engine mount large 4WD, 1pce.

For FG 1/6 4WD competition cars only.Not suitable for conversion of an FG Sportline 4WD models since several small parts required for the swap are not included. As an alternative use item no. y0497.Suitable ball bearing for the layshaft: 6036/05 FG bearing set 10x19x7 with grease filling - 2 pcs

€84.90*

6486 FG Alloy engine mount big for 1:6 2WD Zenoah alloy - 1pce.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

€69.95*

67338 FG Aluminum gear flange engine mount, gear brake

Replacement part for: 67360 Conversion kit for gear brake LeopardContents:1 piece

€152.95*

6264/01 Small aluminum engine mount for FG Leopard 1

This part fits FG Leopard 1/ Leopard Race (built until approx. 2007) with CY / Zenoah G230/240/260/270/290 engine only! Replacement for plastic version FG 6264.Contents:1 piece

€29.90*

y0497 Alloy engine mount large for all FG 4WD Models

Large alloy engine mount for all FG 4WD cars.Contrary to the FG pack this one includes the complete hardware for installation in Sportsline cars as well!

€59.90* €69.90* (14.31% saved)

Customers also viewed

67238 FG Alloy gear flange engine mount Leopard 2WD/4WD

Genuine FG spare/option part.Spare part for the Leopard 2010 2WD/4WD verison.Contents:1 piece

€169.95*

6486 FG Alloy engine mount big for 1:6 2WD Zenoah alloy - 1pce.

Big alloy engine mount suitable for FG 2WD 1/6 cars with CY / Zenoah G230/240/260/270 engine.

€69.95*

y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars

€99.90* €124.80* (19.95% saved)

6011 FG Side guards left/right

Genuine FG spare/option part. Side guards suitable for Marder, Off-Road Buggy 2WD and 4WD body.Contents:2 pieces

€25.00*

GPM Starter cover, no. BJPSCO

Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

y0654 Alloy engine mount big 1:5 2WD for FG Sportsline Zenoah

CNC-cut alloy engine mount for all FG 1:5 and 1:6 Truck models with horizontal engine ahead as Zenoah ZG22, G230RC, G260RC, FG CY23 and CY26.Bearing seat 19 x 7 mm2WD FG 1/5 Sportsline cars do not use a small engine mount. For this application the stock aluminum plate # 7398 is used for engine installation.

€69.90*

FG Off-Road Buggy WB535 4WD

The FG Off-Road Buggy WB535 4WD is presented with a longer wheelbase and a pleasant design. Are you setting value on a well-blanced driving performance with quarantees enough grip and driving fun as well as on functionality and visual appearance? Then the new Off-Road Buggy WB535 is your best choice. Painted body shell to choose, all-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body painted either finished or unpainted. The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. Additionally the 4WD grants the model the maximum driving power and highest fun factor on every surface and in all curves.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg

€989.95*

Configure now