7486 FG Alloy engine mount big 1:5 for Zenoah/Solo

Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece

Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece

Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece

Genuine FG spare/option part. Relocates the starter handle to the roll cage.Wire diameter 1.9 mm.Contents:1 piece

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.A roll cage was installed for more rigidity and protection of the vehicle.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm

Genuine HT spare/option part. Fits all CY / Zenoah engines. Laser cutted stainless steel.The long design increases stiffness of the carburetor assembly significantly compared to the previous version. Comes with gasket and mounting bolt.Content:1 piece