DM4000/01 Alloy servo arm for K-Power, Losi, Savöx, Spektrum, Rhino, Hitec and many more
€13.95
Available
Product information "DM4000/01 Alloy servo arm for K-Power, Losi, Savöx, Spektrum, Rhino, Hitec and many more"
Genuine K-Power spare/option part.
One-piece aluminum servo arm, 67 mm long and 3 mm thick, with 10 linkage hole tapped for M3 screws.
Suitable for all servos with an output shaft with 15 tooth spline shaft, for example:
- K-Power DM4000
- Multiplex Rhino
- Hitec 805
- Savöx SV-0236MG
- Spektrum S9010 and S9020
- LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)
- and many more!
When you count the teeth of your servo you can check if this alloy arm will fit to your servo.
Alloy servo arms are indispensable by strong digital servos, as used on large scale models for example, to optimize the servo forces being transferred.
Content:
- 1 pieces
Login
Customers also viewed
Genuine FG spare/option part.Contents:1 piece
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft!Suitable for all servos with an output shaft with 25 tooth spline shaft, for example:y2006 Digital Big-Scale Servo D-21HV Nearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!holes for linkage with 3 mm diameterWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 piece
This set contains:Top Digital Big-Scale Steering ServoTop Digital Big-Scal Throttle/brake servo 7573 FG Radio controll 2,4 GHz incl. receiverT1257 FG Universal Chargery0425 Y-harness, universal connector2000 mAh 6V Battery with universal connectorWhen used in a FG 2WD car, adaptor plate 6118/02 is required for steering servo installation.
Genuine FG spare/option part. New developed alum. servo arm in high-strength material with M3 threaded holes for the assembly of the throttle pivot posts 06534/02 and 06534/03.Fits Hitech HS-7955 and HS-5585MH.Contents:1 piece
Fits Spektrum SPMS901 Servo.Length: 83 mm.
With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.A roll cage was installed for more rigidity and protection of the vehicle.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm