DYNR0110 Dynamite Alloy Throttle Servo arm 15T for Losi 5ive-T, TLR 5ive-B and Mini WRC

Genuine FG spare/option part. New developed alum. servo arm in high-strength material with M3 threaded holes for the assembly of the throttle pivot posts 06534/02 and 06534/03.Fits Hitech HS-7955 and HS-5585MH.Contents:1 piece

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

The legendary sports car Bugatti EB 110 body shell for 1:5 on-road cars with standard chassis width and 530/535 mm wheelbase. The body shell is vac-formed from 2 mm Lexan.Dimensions:Total length approx. 870 mmTotal width approx. 380/385 mmTotal height approx. 220 mmRequired body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7154/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts The body support FG 7154/01 is screwed directly onto the rear bridge. For attachment to the rear bridge, 2 holes 4 mm must be drilled in them.As a detailing kit (mirrors, windshield wipers!) set # 5435 is recommended (not included!).Since the Bugatti EB 110 1:5 scale body is - just like the original very low, a very low height air filter (#9043) is required. We also recommend 9.5 mm wide wheel squares: #6107 wheel squares 9.5 mm/M6 - 2pcs..For the body side support 32781.