8453/01 FG Front upright for 1:5 with steel ring

€29.90*

Available

Product number: fg_8453_01

EAN: 3410564521779

Product information "8453/01 FG Front upright for 1:5 with steel ring"

Genuine FG spare/option part.

Suitable for all mechanical disk brakes.
Steel insert provides a strong thread for the mounting bolts.

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

y0932 HT Alloy front uprights for FG / Smartech

Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces

€129.90*

Alternatives

y0932 HT Alloy front uprights for FG / Smartech

Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces

€129.90*

Customers also viewed

6429/01 FG Upright front for 1:6 2WD models

Genuine FG spare/option part.Reinforced version with steel inlay to prevent the M5 bolts from being pulled out.Bearing seats: 22 x 7 mm.Contents:2 pieces

€39.90*

4407 FG Axially displaced front aluminium uprights 1,5 mm

Genuine FG spare/option part. With 1,5 mm displaced axial. Fits FG Evo and Competition.Content:2 x Uprights2 x Steering arm2 x Stop unitConsumables

€129.95*

6103/06 FG Alloy upright front 1:6 2WD

Genuine FG spare/option part. Suitable for all FG 2WD 1:6 Off-Road and monster models.Bearing seats: 22 x 7 mm.Contents:1 set

€99.99*

%

500304033D/2.0 Carson 1/5 Wild GP Drift Attack blue 2.4G RTR, 29cc engine, with all accessories

Carson Drift Attack 2.0 special equipment with 60 mm wide front and rear narrow-grip tyres! The off-road tyre for sandy surfaces and spectacular drifts!The model includes the completely installed 2.4 GHz remote control, incl. transmitter alkalines, as well as a fail-safe system (automatic engine cut-off in case of possible malfunctions!), 20kg throttle servo and 35 kg steering servo, as well as a 2.000 mAh 6V receiver battery with charger and a tool set. Furthermore a spare air filter element and a special mixing canister. A detailed multilingual manual is also included.Technical details: - approx. 70 km/h top speed - 0 - 70 km/h approx. 2.5 seconds - With one tank of gas (700ccm) approx. 40 minutes driving time - 29cc engine, with pull starter - Sound reducing tuned pipe exhaust system - 2-shoe clutch with steel clutch bell - A steel differential. - Aluminium shocks, dust protected - bead-lock rims with off-road tyres - aluminium rim driver - adjustable rear wing - Completely ballraced 2WD drivetrain - Water protected receiver box - ventilated double disc brake - aluminium chassis1 piece

€659.95* €839.90* (21.43% saved)

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

y1075 Front brake system for FG Marder, FG Off-Road Buggy and for Carson / Smartech 2WD offroad cars incl. uprights, bearings and axles

Complete pre-assembled set front disc brakes for FG Marder, FG Off-Road Buggy and for Carson / Smartech Attack / Comanche / UNO / Monster Truck / CRT / CPT / Super Attack / Evo Attack / Spider / Big Attack , fits Conrad Big Pyro as well.For mounting in a Gas Blaster you must change you front shock mount and the front body shell holder, look at the pictures. Includes:- brake system with linkage- uprights- bearings- longer axle shafts- wider square drivesNo additional parts needed.

€179.90*

y1421 Engine quick mount for G320 Zenoah in FG 1/5 scale

y1421 Versiown: y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³

Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!

€74.95*