Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
Genuine GPM spare/option part. The Big Scale-Cross clutch is equipped with 1.3 mm springs, is especially suitable for Off-Road use.Adjustable 3-shoe clutch for:ZenoahChung YangHPI - FueliSmartech PTAnd many other enginesThe GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!y0730y0731Content:1 piece
With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90
Genuine FG spare/option part. Spare part for Zenoah ZG22, G230RC, G230RC 04 and G260RC.Zenoah bolts 7318 are required for installation.Contents:2 pieces
Genuine Dynamite spare/option part.The Dynamite clutch tool works with all CY and Zenoah large scale gasoline engines (except G320).Locks the crankshaft in place for ease of engine maintenance such as standard clutch repair/replacement, flywheel replacement and general engine overhauls.Made of CNC machined billet aluminum and anodized red.
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
Genuine GPM spare/option part. The Big Scale-Cross clutch is equipped with 1.3 mm springs, is especially suitable for Off-Road use.Adjustable 3-shoe clutch for:ZenoahChung YangHPI - FueliSmartech PTAnd many other enginesThe GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!y0730y0731Content:1 piece
With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90
Genuine FG spare/option part. Spare part for Zenoah ZG22, G230RC, G230RC 04 and G260RC.Zenoah bolts 7318 are required for installation.Contents:2 pieces
The new adjustable system features three carbon pads with special 2.4 mm springs.Weight of the complete clutch is 70 grams. Very wear resistent when running with the recommended clutch bells.Adjustable friction points: First gear - 8.500 U/min. Second gear - 9.300 U/min. Third gear - 10.100 U/min. Fourth gear - 11.000 U/min.With tool #5445 the engagement speed can be adjusted to different settings within a range from about 8,500 to 11,000 rpm.
Genuine FG spare/option part. Spare part for Zenoah ZG22, G230RC, G230RC 04 and G260RC.Zenoah bolts 7318 are required for installation.Contents:2 pieces
Complete RTR 2x TT1530/350 TT 5000 mAh LiPo Batteries 3S, 7,4V 60C y1580 HT T240 Duo AC/DC, 2 x 120W, bis 6S, Charger 2x TT1499 Top Tuning Safety Bag für LiPo Batteries Genuine FG spare/option part.The electric powered version of the legendary Marder buggy is equipped with a powerful 1100kV 2800W brushless motor. Power supply: 6S or 6S Li-Po battery pack. In its entry level version 6S, the running time is about 15 minutes with lightning-accelerations and a top speed superior to the gas powered Marder one. In the 6S configuration, the E-Marder is a true rocket ship!In the first place our 1:6 Off-Road Buggy stands for driving fun. Through the knobbed tires or with Slick tires (optional extras) the model can be driven cross-country, on a car park, simply just everywhere.The RTR version of the car includes servo, transmitter, receiver, transmitter / receiver and rechargeable batteries. 2WD Off Road BuggyMachined 4 mm aluminum chassis plate with side guardsIndependent suspension with many options for adjustmentRoll cage, can be used as a carrying handle as wellClosed factory painted body shell with decals already appliedFlange rims with knobby tires1100 kV-2800 W motor150A brushless ESCTwo locations for the batteries with hook-and-loop strapsDimensions:Length: 620 mmWidth: 420 mmHeight: 260 mmWheelbase: 470 mmWeight: 6,4 kgContents:1 piece
Genuine FG spare/option part. New version clutch bell for all FG cars except Formula 1. Contrary to the previous version 6049 the flat areas for the pinion set screws are angled at 90° instead of 180° (see pic).Dimensions:Shaft diameter 10 mmShaft length 38,2 mmOverall length 61 mmAouter diameter bell 58 mmInner diameter bell 56 mmContent:1 pieces
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
€9.90*
This website uses cookies to ensure the best experience possible. More information...