y19133 Ball & socket tool
€27.90
Available
Product information "y19133 Ball & socket tool"
Ball & socket tool with t-handle, especially for installation and removal of balls in FG or Smartech/Carson cars' plastic a-arms and steering rod ball joints.
Contents:
- 1 piece
Login
Customers also bought
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
This pair of Tyres have the following use indications: HIGH GRIP situation for clean track. HIGH GRIP situation for big asphalt. HIGH GRIP situation for high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!
Genuine HT spare/option part. For the optimal measurement of the chassis.Steel rulers, 150 and 300 mm long.Contents:2 piece
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g
Content: 30 Gramm (€796.67 / 1000 Gramm)
Genuine FG spare/option part. Gilmer belt pulley with 40 teeth for the front axle of FG 4WD models. Improves the propulsion of the front axle through increased rpm.Content:1 piece
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece
Customers also viewed
For ball bearings (diameter 8 x 22 mm) in steering blocks and uprights.Instructions:Remove the M5 bolt until the gap between the bolt's head and the top of the spindle is slightly more than the the width of the bearingInsert the spindle with the bolt into the bearing and srew the bolt in with an allen key from the opposite (do not tighten the bolt!)Now remove the bearing by just turning the spindle ccw
Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece
Genuine HT spare/option part. With non-slip surface perfect for delicate work, actually improving dexterity and grip.Available sizes: 8, 9 and 10.Glove size?Size 8 = 21 cm (S - L) circumferenceSize 9 = 24 cm (L - XL) circumferenceSize 10 = 27 cm (XL - XXL) circumferenceMeasure the circumference of your hand without the thumb and at the widest point (above the ankle). The tape measure should embrace the hand loosely.Norm EN388, Lining 100% polyamide.Partially coated with hightech nitrile Fits like a second skinGrips even when wetGood touch sensitivityLiquid-repellentGood resistance against oil and greaseContents:1 pair / 2 pieces3 pairs / 6 pieces
Genuine FG spare/option part.Handy auxiliary tool to press-in ball bearings, guide bushes a.s.o. A jaming of ball bearings or guide bushes is almost impossible. Also suitable for dismounting of cooling fans and clutches at Zenoah engines. For Solo only suitable for cooling fans.
Tool and screw tray with quick-mount clamp, fits tubes with a diameter from 32 to 35 mm. Thus perfectly suitable for the TopTuning Car Stand TT1030 and for many other holders.Due to a strong design with high quality materials, a very high load capacity is achieved. Many possibilities to store tools and small parts to have them handy at any time when working with the Car Stand. The adjustable clamp allows the mounting of more than one Tool Tray. Contents: with foldable Tool Tray with milled adapter block with mounting clamp
Genuine FG spare/option part.Auxiliary tool to mount and dismount the ball-type nipples 4466, a jaming is impossible. The use is only in connection with the FG mounting device 8538 possible.
Retrofitable bowden cable disk brakes for Formula 1 Sportsline and Competition models. Essentially improved brake power compared to the standard brake, sensitive adjustment.