Typical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 3C when time is criticalRecommended charge with 2 3CConnectors: EC5, XH-balancer.Dimensions: Length +/- 5 mm: 138,5 mmWidth +/- 1,5 mm: 47 mmHeight: +/- 1,5 mm: 36,5 mmWeight +/- 10g: 363gContents:1 piece
PMT tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine PMTspare/option part. PMT - large scale slick 2019Winner of all three 1/5 EFRA Grand Prix races this year, as well as in the ELS Cup Luxembourg:April 28th: 1st EFRA Grand Prix at Lostallo, CHMay 26th: 2nd EFRA Grand Prix at Leipzig, GermanyJune 23rd: 3rd EFRA Grand Prix at Groningen, NLAugust 11th ESL-Cup LuxembourghRecommended use according to the manufacturer PMT: H - Hard, as front tires on very grippy asphalt and at high temperatures M - Medium, as front tires on normal asphalt and at normal temperatures S - Soft, as rear tires on normal asphalt and at normal temperatures SS - Ultra Soft, as rear tires on less grippy asphalt and at lower temperatures Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square driveContents:2 piece
Genuine FG spare/option part. Suitable for all FG touring car und Race-Truck models with long wheel base.Dimensions:Total length: 255 mmMounting bolt distance: 220 - 240 mmContent:1 piece
Genuine FG spare/option part. FG ball bearing with heat resistant grease filling up to 180°. Therefore essentially improved durability of the wheel bearings and the clutch bell.For all FG cars with alloy differential case except 4WD and Formula 1.Contents:Eight pieces: 8 x 22 x 7 mmTwo pieces: 10 x 22 x 6 mmTwo pieces: 10 x 19 x 7 mmTwo pieces 15 x 28 x 7 mm
y2003 Model:
y2003/03 - FG 4WD Marder and FG touring cars with 510 mm wheelbase: Mini Cooper and Porsche GT3 RSR
Tuning front suspension set for all FG 4WD Sportsline cars: Monstertruck; Baja; Marder; Beetle; touring cars:Not fit Formular 1, Leopard and Truggy!y2003/01 fits:FG 4WD Monster-Truck models, Beetle.Part number:Name:y68412Aluminum front lower a-armsy2000Alu Querlenker Front unteny68413Aluminum front uprightsy0563Aluminum shock tower Monster-Truck/Beetley1036Rose joint for alloy wishboney2003/02 fits: FG 4WD Baja Buggy.Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishboney0579Alloy roll cage brackety2003/03 fits:FG 4WD Marder and FG touring cars with 510 mm wheelbase: Mini Cooper and Porsche GT3 RSR. When installing in a Porsche GT3 RSR or Mini Cooper 4WD with 510 mm wheelbase, the steering travel limiter must be installed into the first threaded hole of the knuckle arm and not at the standard location on the knuckle as in off-road cars!Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishbone
FG Set price: 130,20 EURFits all FG touring cars, GT-models and Mecatech FW01.The ball drive conversion kit for FG marder, Off-Road Buggy, beetle, monster / stadium, formula 1 and truck models you will find under GPM 9472. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM ball drive set includes everything for a conversion of the respective FG/Mecatech cars. Set includes:Quantity:DescriptionPart number2 piecesBall drive wheel shaftGPM 6079/012 piecesDifferential ball drive cupGPM 6069/022 piecesBall drive shaft 91 mmGPM 7081/014 piecesDrive shaft booty100412 piecesSteel ballGPM 7080/024 piecesDrive shaft spacer springy1218
Alloy rear axle conversion kit for all FG 1/5 Sportsline cars except Formula 1 and Race Truck.The set includes:- rear plate- differential mounts- riser plates- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075 instead of 6073!
Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Short fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size of 40 x 40 x 10 mm can be swapped e.g. for the fans of the FG motor cooling unit or the fans of various speed controllers.The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 40 x 40 x 10 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 16,000 rpm @ 8.4 V Air flow: 16.7 cfm Connector: Dupont 2-pin female (compatible with BEC/Futaba/Universal) Cable length: approx. 17 cm Contents:1 piece
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 50 x 50 x 15 mm can be swapped e.g. for the fan of the ARRMA motor cooling unit or the fans of different speed controllers (e.g. ZTW Beast 200A). The ARRMA application requires approx. 5 mm longer screws due to the 5 mm taller fan (M4x25).The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 50 x 50 x 15 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 10,000 rpm @ 8.4 V Air flow: 28.3 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece
Genuine GPM spare/option part. Milled 6061T6 aluminum additional heat sink from GPM with larger 12 volt fan (60 x 60 x 15 mm) for Arrma Kraton / Outcast 8S. The additional heat sink also serves as an adapter plate to mount the larger fan on the original heat sink. A machined contact guard for the intake side of the fan is also included.The fan is connected to the EC5 connector of a 3S or 4S drive battery using an adapter cable (included). Thus, the operating current does not have to be provided by the ESC's BEC.The overall height of the unit, measured from the bottom of the additional heat sink is about 30 mm.Contents:1 set
Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Long fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 60 x 60 x 24 mm can be swapped e.g. for the fan of the ZTW Beast 300A speed controller. For this particular application, M4x40 screws are required instead of the standard M4x30 screws due to the 9 mm taller fan.The air flow is considerably higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 8.4 V Current: 0.5A Speed: 8,500 rpm @ 8.4 V Air flow: 39.2 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece