Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Short fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size of 40 x 40 x 10 mm can be swapped e.g. for the fans of the FG motor cooling unit or the fans of various speed controllers.The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 40 x 40 x 10 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 16,000 rpm @ 8.4 V Air flow: 16.7 cfm Connector: Dupont 2-pin female (compatible with BEC/Futaba/Universal) Cable length: approx. 17 cm Contents:1 piece
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 50 x 50 x 15 mm can be swapped e.g. for the fan of the ARRMA motor cooling unit or the fans of different speed controllers (e.g. ZTW Beast 200A). The ARRMA application requires approx. 5 mm longer screws due to the 5 mm taller fan (M4x25).The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 50 x 50 x 15 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 10,000 rpm @ 8.4 V Air flow: 28.3 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece
Genuine GPM spare/option part. Milled 6061T6 aluminum additional heat sink from GPM with larger 12 volt fan (60 x 60 x 15 mm) for Arrma Kraton / Outcast 8S. The additional heat sink also serves as an adapter plate to mount the larger fan on the original heat sink. A machined contact guard for the intake side of the fan is also included.The fan is connected to the EC5 connector of a 3S or 4S drive battery using an adapter cable (included). Thus, the operating current does not have to be provided by the ESC's BEC.The overall height of the unit, measured from the bottom of the additional heat sink is about 30 mm.Contents:1 set
Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Long fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 60 x 60 x 24 mm can be swapped e.g. for the fan of the ZTW Beast 300A speed controller. For this particular application, M4x40 screws are required instead of the standard M4x30 screws due to the 9 mm taller fan.The air flow is considerably higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 8.4 V Current: 0.5A Speed: 8,500 rpm @ 8.4 V Air flow: 39.2 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Genuine FG spare/option part.Cooling fan for electric engine no.: 7900 FG Electric engine E-Power BL-730KV.
€39.95*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).