Product information "LOS251099/01 ZTW 300A ESC mounting bracket for DBXL-E 2.0"
Genuine Losi spare/option part.
The esc mounting bracket is equipped with an extremely strong double-sided adhesive tape for fixing the controller. Additionally the esc can be secured with the Top Tuning Velcro TT1021/12, which you can select from the shopping options.
Compared to the standard plate, the support surface has been widened by 1mm, so that the ZTW 300A controller can be mounted ideally; slipping back and forth is securely avoided.
Contents:
1 set
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Genuine Top Tuning spare/option part. Motor adapter plate to mount the ZTW 620KV Beast motor into the Losi DBXL-E 2.0. The plate has four mounting holes, which should also be used due to the enormous torque of the ZTW motor. In order to install the screw at the l/h top position, at least 0.6mm material must be removed from the existing motor/differential mount. Contents:1 piece
Complete set of 22 sealed ball bearings for Losi DBXL-E 2.0 and Desert Buggy XL 1/5.Set includes:16 pieces of 12 x 24 x 6 mm sealed bearings (axle shafts / differentials / clutch bell)4 pieces of 10 x 22 x 6 sealed bearings (bevel pinion shafts)2 pieces of 8 x 19 x 6 sealed bearings (intermediate shaft)Total: 22 sealed bearingsPrice when bought separately: 95.92 EUR
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Genuine Top Tuning spare/option part. Motor adapter plate to mount the ZTW 620KV Beast motor into the Losi DBXL-E 2.0. The plate has four mounting holes, which should also be used due to the enormous torque of the ZTW motor. In order to install the screw at the l/h top position, at least 0.6mm material must be removed from the existing motor/differential mount. Contents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Fits BP70120 ZTW Beast Brushless motor 620 kV.Bolt pattern: 4 x for M4 screws on 30 mm pitch circleDistance center of motor / base plate: 37 mmContents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Available with the following diameters:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard Baureihe 58Diameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kV, requires the taller TT1021/01B Top Tuning Motor mount for ZTW Beast motorDiameter 55,75 mmContents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Bolt pattern: 4 x 30 mm pitch circle for M4 screwsDistance center of motor / base plate: 32 mmContents:1 piece
Genuine Top Tuning spare/option part. Spare part for electric conversion kit TT1021 or for your own designs.Available with the following diameters:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard Baureihe 58Diameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kV, requires the taller TT1021/01B Top Tuning Motor mount for ZTW Beast motorDiameter 55,75 mmContents:1 piece
The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 535 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads!Dimensions: Length: 880 mm Width: 392 mm Height: approx. 240 mm Wheelbase: 530 mm The car comes with an unpainted body shell!Touring cars in action!Painting tips:
Inclusive: y1580 HT T240 Duo AC/DC, 2 x 120W, up to 6S, charger 2x TT1530/450 Top Tuning 5000 mAh LiPo battery 4S, 14,8V 60C Body shell to choose!LOS05020V2T1 - Fox KarosserieLOS05020V2T2 - Losi Karosserie The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers demand including the Spektrum Firma® 160 Amp Brushless SMART ESC and Spektrum Firma 4-Pole 780Kv Brushless Motor allowing you to hit 50+ MPH with an 8 cell LiPo battery. Finally, the DBXL-E 2.0 has a Losi race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance. Spektrum Firma® 160 Amp Brushless SMART ESCThe ESC is waterproof, completely programmable, and comes pre-wired with a high-current IC5 connector. The ESC will work with most sensorless brushless motors and is Li-Po and Ni-MH compatible. The SMART technology provides information like battery voltage, RPM, RX pack Voltage, and Speed directly from the ESC when used with the Spektrum Dashboard app. 50+ MPH Spektrum Firma 4-Pole 780Kv Brushless MotorThe brushless ESC and motor provide wicked power with an 8s LiPo battery (not included) that will blaze speeds of 50+ MPH. Spektrum S906 1: 5-MetallgetriebeservoNeues 30-kg HV Hi-Torque Metallgetriebe-Servo. New Chassis Braces In addition to the chassis stiffening plate, we have also added an additional electric specific rear chassis brace that goes all the way up to the center diff mount to increase the rigidity of the chassis. Updated Front and Rear BulkheadsThe front and rear bulkheads have been updated to match the new gearboxes designed for the DBXL-E 2.0. Two additional mounting locations were added to the side of the bulkheads to keep the gearboxes from rocking up and down under acceleration and braking. This provides a more stable drivetrain, and increased overall durability. Aluminum Center Diff CupReturning from the original DBXL-E is the aluminum diff cup used in the center differential. Today"s brushless motors produce so much power, that you need to have the added strength and durability in the center diff that only an aluminum diff cup can provide. New Shocks with Laser Etched FOX Logo Shock CapsNew shock bodies with a lower aluminum cap that allows for easier maintenance of the shock seals for improved performance. Sometimes, it is about the details. New upper shock caps with laser etched FOX logo set off that race inspired look. MAXXIS Creepy Crawler Tires with Authentic Bead Lock WheelsGenuine MAXXIS creepy crawler tread pattern tires provide added traction and offer extra control so you can stop, turn and swerve like a pro. Have confidence your tires will never come unglued and make tires changes a breeze with authentic bead lock wheels. Aluminum Shock TowersWe couldn"t just stop at the shocks. The DBXL-E 2.0 gets all new Aluminum Shock Towers Front and rear with revised camber mounting locations for improved stability and handling. Heavy Duty DrivetrainIncreased the size of the out drives and drive shaft to support a larger 5mm drive pin for increased strength and durability. New Radio TrayAll new radio tray with sealed receiver box. The new radio tray allows for multiple steering servo configurations. Can be run as a single servo, or updated to run dual steering servos for maximum steering performance. New ESC MountTo create space for the larger battery trays, we needed to find a new home for the ESC. The ESC has been relocated to a mounting plate off the center differential. This allows for optimal weight distribution within the car, while increasing the air flow over the top of the ESC for better running performance. New Race Themed LiveryNew Fox Shox race inspired Motorsports themed livery for that true off-road look, along with an awesome Losi flame design trim scheme. Waterproof ElectronicsThe DBXL-E 2.0 is loaded with waterproof electronics including the receiver, servo and ESC. Everything is sealed against the elements allowing you to splash in the rain, spin in the mud and make tracks in the snow. It"s full-throttle freedom to run anytime, rain or shine LED Light BarThe roof mounted LED Light bar from the original DBXL-E returns to continue lighting the way for endless adventures. Spektrum DX3 Radio SystemThe Spektrum DX3 radio system offers advanced features like AVC control, a 3-position throttle limiting switch and travel adjust. It features exclusive DSMR® technology for superior range, response, and interference resistance. It's also fully compatible with the Smart telemetry potential provided by the vehicle's installed Spektrum Firma Smart 40A ESC/receiver, and has a convenient voltage level indicator for any Spektrum Smart batteries! The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures Spektrum Firma® 160 Amp Brushless SMART ESC Spektrum Firma 4-Pole 780Kv Brushless Motor Spektrum DX3 radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Waterproof Components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar
Genuine rc-car-online spare/option part. A "must have" for every run in the dark. A total of 11 different lighting effects are programmeded into this LED module. The LED strip has the same size like that of the Losi 5ive-T 2.0 and the Losi DBXL-E and can therefore replace for the OEM version in its bracket.The LED module is typically powered by the receiver battery (maximum 7.4V). Depending on the version selected, the effects are changed via the radio (requires a free channel on transmitter and receiver) or via an onboard switch.The LED strip has on the back of an adhesive strip with which it can be glued on loose on the body. In the shop's options menu you can add an optional mounting bracket for the Losi 5ive-T. Modes:Continuous whiteContinuous white 30% intensityOffKnightRider redKnightRider whiteKnightRider blueKnightRider greenPolice 1Police 2SafetyCarRainbow chaser lightStrobo-Light whiteDimensions LED:Length: 160 mmHeight: 10 mmDimension mount:Width: 160 mmHeight orifice: 8 mmHeight behind orifice: 10 mmContents:1 set
€67.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).