Genuine Speed Tec spare/option part. Speed TEC Tuning Ignition Löhin RS4 332 new ignition system with offset ignition timing and modified spark breakaway. Advantage of the ignition system: better starting and acceleration due to the modified ignition timing. Higher ignition voltage through modified spark breakaway, resulting in increased charging time for the coil, thereby considerably more torque in the medium rpm range. Suitable for Zenoah and CY engines without modifications. In the picture you can see the original Löhin ignition.Contents:1 piece
New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361). For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels! The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course. This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine! The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine! The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling! As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing. This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase. Other benefits of SPEED TEC CIS - ignition system: Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320) No modifications to the cylinder or the ignition coil mount required! No assembly of the flywheel, thus 100% exact fit and running true The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm! The baffles protect the flywheel from debris (stones, etc.) Complete with Löhin ignition and all necessary parts in a nice special bag Easy installation: Remove the stock ignition system - install the CIS-ignition - done! The color of the ignition cable and the spark plug cap may vary.
The use of NGK spark plug caps with noise suppression resistor offers an optimal suppression of RFI in all frequency ranges without negative effects on engine performance.NGK spark plug caps are equipped with a resistor element made of high quality ceramic material. This ensures a constant resistance value with only a slight deviation in overload conditions. Features: Material: phenolic resinType: 90 degreeColor: Black Resistance: 5 kilo ohms RFI suppression: Yes Waterproof: Yes Cable length: Without cable Connection: SAE terminal nut or integrated terminal Features: Compact type; only 31.5 mm high
PMT tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine PMT spare/option part. The Supreme have been designed for all track conditions. Developed with latest generation components, deriving directly from the highest level of Motorsport, they are available in three hardnesses:SS "NEW": supersoft, 35 shore hardness, suitable for rear and slightly abrasive asphaltsS00 (K00): soft, 38 shore hardness, suitable for rear and slightly abrasive asphaltsM00/P1 (K01): medium, 42 shore hardness, suitable for rear / front and medium abrasive asphaltsH00/P1 (K03): hard, 45 shore hardness, suitable for front and very abrasive asphaltsOn this type of tyres a new lighter and harder rim will be used, designed to withstand 25% higher lateral forces, compared to existing ones.Moreover, even the filling mousse has been updated and can now withstand up to a temperature of 130 °, without altering its mechanical characteristics. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square drive Contents:2 pieces
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
PMT tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine PMT spare/option part. The Supreme have been designed for all track conditions. Developed with latest generation components, deriving directly from the highest level of Motorsport, they are available in three hardnesses:SS "NEW": supersoft, 35 shore hardness, suitable for rear and slightly abrasive asphaltsS00 (K00): soft, 38 shore hardness, suitable for rear and slightly abrasive asphaltsM00/P1 (K01): medium, 42 shore hardness, suitable for rear / front and medium abrasive asphaltsH00/P1 (K03): hard, 45 shore hardness, suitable for front and very abrasive asphaltsOn this type of tyres a new lighter and harder rim will be used, designed to withstand 25% higher lateral forces, compared to existing ones.Moreover, even the filling mousse has been updated and can now withstand up to a temperature of 130 °, without altering its mechanical characteristics. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square drive Contents:2 pieces
The 2WD-465 Sportsline model is built on the short chassis with double a-arms suspension front and rear. The vehicle is equippedwith the 2-shocks front suspension as standard, which ensures optimum traction for both front wheels.On the GT2, the front axle has been widened to 384 mm. The rear axle is 395 mm wide.Technical description:The model has a 465 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.The FG 5164 decor sheet is not included!Also available painted in the shop selection!Dimensions: Length: 840 mm Width: 395 mm Height: 250 mm Wheelbase: 465 mm Touring cars in action!Painting tips:
New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361). For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels! The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course. This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine! The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine! The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling! As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing. This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase. Other benefits of SPEED TEC CIS - ignition system: Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320) No modifications to the cylinder or the ignition coil mount required! No assembly of the flywheel, thus 100% exact fit and running true The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm! The baffles protect the flywheel from debris (stones, etc.) Complete with Löhin ignition and all necessary parts in a nice special bag Easy installation: Remove the stock ignition system - install the CIS-ignition - done! The color of the ignition cable and the spark plug cap may vary.
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).