y1387/04 SPEED TEC replacement ignition coil for SV012 ignition

Genuine Speed Tec spare/option part. Speed TEC Tuning Ignition Löhin RS4 332 new ignition system with offset ignition timing and modified spark breakaway. Advantage of the ignition system: better starting and acceleration due to the modified ignition timing. Higher ignition voltage through modified spark breakaway, resulting in increased charging time for the coil, thereby considerably more torque in the medium rpm range. Suitable for Zenoah and CY engines without modifications. In the picture you can see the original Löhin ignition.Contents:1 piece

Please note:The usual spare parts supply is not yet available for these engines. Therefore the parts may come from disassembled new engines. Since every single engine is tested at the factory, the parts may show some minor signs of "use".

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361). For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels! The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course. This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine! The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine! The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling! As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing. This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase. Other benefits of SPEED TEC CIS - ignition system: Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320) No modifications to the cylinder or the ignition coil mount required! No assembly of the flywheel, thus 100% exact fit and running true The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm! The baffles protect the flywheel from debris (stones, etc.) Complete with Löhin ignition and all necessary parts in a nice special bag Easy installation: Remove the stock ignition system - install the CIS-ignition - done! The color of the ignition cable and the spark plug cap may vary.

incl. assemblyThe DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools

The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 535 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads!Dimensions: Length: 780 mm Width: 392 mm Height: approx. 240 mm Wheelbase: 530 mm The car comes with an unpainted body shell!Touring cars in action!Painting tips:

Genuine FG spare/option part.For Zenoah G230/240/260/270/290/320 enginesContents:1 piece