Accelerator-spray is the second component to cure superglue immediately.This set is also particularly suitable for the possible repair of loosened tire/rim gluing!Advantages:Tangible adhesion after a few secondsAromatic solvents and hexane freeSuitable for hobby, craft, industry and householdProcessing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.Contents:Special tire cement ht 4000Spray can activator
Item N° y0285 Accelerator - 1pce.For all tire adhesives above,150 ml spray canAccelerator-spray is the second component to cure superglue immediately.Advantages:Tangible adhesion after a few seconds Aromatic solvents and hexane free Suitable for hobby, craft, industry and household. Processing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 170 mmWidth: 65 mmWeight: 367 gramContent:2 pieces / 1 pair
For technical reasons we had to modify the square wheel adapter of the new Off-Road wheel 2011. Therefore it is necessary to mount the 12mm alum. square wheel driver (ItemN°. 06107/07) for this wheel. After the assembly of this square wheel driver it is possible to drive also GRP or Hörmann wheels without any further modifications. We have marked the Off-Road wheel 2011 on the inside with the number 1.
HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 18 mm square socket and reinforced silver headlock rings for FG, Smartech and many more. 150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. The GPM Ultragrip are designed for use on sandy surfaces.We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 18 mm square wheel drive Regular price EUR 177,40The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 170 mmWidth: 65 mmWeight: 367 gramContent:2 pieces / 1 pair
For technical reasons we had to modify the square wheel adapter of the new Off-Road wheel 2011. Therefore it is necessary to mount the 12mm alum. square wheel driver (ItemN°. 06107/07) for this wheel. After the assembly of this square wheel driver it is possible to drive also GRP or Hörmann wheels without any further modifications. We have marked the Off-Road wheel 2011 on the inside with the number 1.
Item N° 67210/05 Mini Pin M / OR tires, Leo wheel white, glued, 2pcs. Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (Item-no.: FG 6107/07). The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Item N° 67214/06 Mini block H / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Item N° 67210/02 Mini Pin M/ OR tires, with inserts, 2 pcs.Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. These tires fit all 1:6 scale wheels with Ø110mm and a width of approx. 64mm. Suitable inserts are enclosed.
Item N° 67210/01 Mini Pin S/ OR tires, with inserts, 2 pcs.Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. These tires fit all 1:6 scale wheels with Ø110mm and a width of approx. 64mm. Suitable inserts are enclosed.