6118/10 FG RC mounting set 1:6 for 2 brakes, set

€19.90*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6118_10

EAN: 3410569685704

Product information "6118/10 FG RC mounting set 1:6 for 2 brakes, set"

Item N° 6118/10
RC mounting set 1:6 for 2 brakes, set

For installation of 2 disk brakes at front and rear axle you need the rc mounting set.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

6534/02 FG Throttle pivot post

Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.

€7.90*

y0735 Safety clip for Universal / JR / Futaba connectors

Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece

€1.50*

6540 FG Receiver box

Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece

€13.90*

6268 FG Battery holder - 1pce.

€13.90*

5014/05 FG Bolt for battery holder

Genuine FG spare/option part.Plastic bolt for battery holder.Contents:2 pieces

€5.90*

5014/06 FG Battery holder short

Genuine FG spare/option part. Suitable for all FG touring cars with short or medium wheel base.Dimensions:Total length: 225 mmMounting bolt distance: 190 - 210 mmContents:1 piece

€14.90*

y1588 Aluminum receiver antenna mount

Genuine rc-car-online spare/option part. Versatile aluminum bracket for easy installation in panels or RC boxes with up to 4 mm wall thickness. Only a 6 mm hole is required and the bracket is fastened with the included nut. Alternatively, for installation in thicker material an M6 thread can be tapped as well. An O-ring provides a seal when installed in RC boxes.The bracket has a stepped hole into which the common antenna tubes of about 3.2/3.3 mm diameter can be inserted, but not pushed through. The hole for the antenna cable has a diameter of approx. 2.5 mm.The height of the bracket above the mounting surface is 16 mm.The scope of delivery includes an end cap and two antenna tubes with a length of approx. 170 mm.Contents:1 set

€9.90*

5014/04 FG Servo adapter frame, Futaba/JR, Thunder Tiger DS1015

Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces

€11.90*

TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch

tt_tt1000 Connector: TT1000/01 Universal in - Universal out

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

€39.90*

10802 Aluminum transponder mount

Genuine HT spare/option part.For installation of the personal transponder.Contents:1 piece

€9.95*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

6815/03 FG Alloy mounting bolts bilateral with 4mm screw thread

Genuine FG spare/option part. Bolts for 6815.Dimensions: 8 x 37,5 mm.Contents:4 piece

€7.10*