Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

60214/06 FG Off-Road Buggy tires S narrow glued, black

Product information "60214/06 FG Off-Road Buggy tires S narrow glued, black"

Genuine FG spare/option part. 

1:/6 Off-Road Buggy tires, soft, glued on FG Off-Road buggy-rim black. Outer Ø 175 mm, width 65 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.

Contents:
  • 2 pieces

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Alternatives

%

Average rating of 0 out of 5 stars

y0658 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co., 18 mm square drive
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.Contents:2 pieces / 1 pair

€39.90* €59.90* (33.39% saved)

Average rating of 0 out of 5 stars

y0658/02 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co with 24 mm hex
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

€39.90*

Average rating of 0 out of 5 stars

y0580 Mammoth Supergrip for 1/6 and 1/5 offroad cars glued
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.90*

Average rating of 0 out of 5 stars

y1172 Mammoth offroad tires extra wide, mounted and glued on original FG 1:6 rim, 2 pcs.
Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!Diameter 165 mm, width 80 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:softhard Unit price:- Mammoth tires extra wide: EUR 47.20 / pair- Mammoth inserts extra wide: EUR 9.90 / pair- genuine FG wide track rims 6105/01: EUR 14.90 / pair- genuine FG rim extension rings 6436: EUR 14.90 / pair- mounting + glueing rims / extensions / inserts / tires: EUR 13.00Total: EUR 99.90 Priced per pair.We have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. With few exceptions, the Mammoth is usually for the rear axle only. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels with extension rings and wide tire inserts (same as for the FG wide slicks), which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Also suitable for:With the following wheel adapter: y1183 Rim adapter

€69.90*

Average rating of 0 out of 5 stars

y0617 The offroad super combination - Front V-Pin / Rear Mammoth, 1 pair each (2 pairs in total)
The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairRims FG 6105/01 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EUR Total EUR 78.80 EUR Description for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 6105/01: 14.90 EUR / pairgenuine FG rim extension rings 6436: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EUR Total: 99.90 EUR Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.99*

Average rating of 0 out of 5 stars

y1406/01 MadMax BIG DIGGER 170x80/x60 for HPI + Losi (24 mm hex drive)
BIG DIGGER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange beadlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.The MadMax tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€119.90*

Accessories / Spare parts

Average rating of 0 out of 5 stars

60200 FG Rim Off-Road Buggy, rear
Genuine FG spare/option part. Rims for FG Off-Road Buggy rear.Diameter x width: 140 x 75 mm18 mm wheel squareContents:2 pieces

€24.95*

Average rating of 0 out of 5 stars

60220 FG Tire inserts Off-Road Buggy wide
Genuine FG spare/option part. Dimensions:Length: 475 mmWidth: 80 mmHeight middle: 17 mmHeight side: 12 mmContent:2 pieces

€9.30*
%

Average rating of 0 out of 5 stars

y0658 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co., 18 mm square drive
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.Contents:2 pieces / 1 pair

€39.90* €59.90* (33.39% saved)

Average rating of 0 out of 5 stars

y0658/02 Narrow-Grip 462 type tires for Losi, HPI, FG, Carson and Co with 24 mm hex
Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

€39.90*

Average rating of 0 out of 5 stars

y0580 Mammoth Supergrip for 1/6 and 1/5 offroad cars glued
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.90*

Average rating of 0 out of 5 stars

y1172 Mammoth offroad tires extra wide, mounted and glued on original FG 1:6 rim, 2 pcs.
Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!Diameter 165 mm, width 80 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:softhard Unit price:- Mammoth tires extra wide: EUR 47.20 / pair- Mammoth inserts extra wide: EUR 9.90 / pair- genuine FG wide track rims 6105/01: EUR 14.90 / pair- genuine FG rim extension rings 6436: EUR 14.90 / pair- mounting + glueing rims / extensions / inserts / tires: EUR 13.00Total: EUR 99.90 Priced per pair.We have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. With few exceptions, the Mammoth is usually for the rear axle only. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels with extension rings and wide tire inserts (same as for the FG wide slicks), which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Also suitable for:With the following wheel adapter: y1183 Rim adapter

€69.90*

Average rating of 0 out of 5 stars

y0617 The offroad super combination - Front V-Pin / Rear Mammoth, 1 pair each (2 pairs in total)
The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairRims FG 6105/01 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EUR Total EUR 78.80 EUR Description for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy rims 6105/01 with extension ring!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 6105/01: 14.90 EUR / pairgenuine FG rim extension rings 6436: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EUR Total: 99.90 EUR Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.99*

Customers also bought

Average rating of 0 out of 5 stars

60210/06 FG Off-Road Buggy tires M wide glued, black
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim black. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€107.95*

Average rating of 0 out of 5 stars

y0962/02 FG manuals set Off-Road Buggy 4WD Competition English/German, set
y0962_02 Language: German
Item N° y0962/02 FG manuals set Off-Road Buggy 4WD Competition English/German, setGenuine FG manuals as included with the cars.

€3.90*

Average rating of 0 out of 5 stars

SPM2340 Spektrum DX3 Smart 3-Channel Transmitter with SR315 Receiver
The DX3 is much more than an economical 3-channel transmitter. Together with the included SR315 receiver, it's the most affordable radio system that offers the superior range, response, and interference resistance of exclusive Spektrum DSMR technology. Plus, drivers using the DX3 are also equipped to enjoy the breakthroughs of innovative Spektrum Smart Technology.Install a Spektrum Smart LiPo battery and Smart Firma ESC in your model, and you can view vehicle battery capacity at a glance on the DX3 transmitter's convenient voltage level indicator.Features DSMR® Technology for superior range, response and interference resistance 3-Channel operation (Steering, Throttle, AUX1) Smart Technology ready with the included SR315 receiver New styling focused on ergonomics Foam covered steering wheel for better control Convenient voltage level indicator for Smart batteries Supports the on-demand traction control of AVC® technology Servo reversing and trim dial 3-position throttle limiter ERGONOMIC TRANSMITTER DESIGNThe ergonomic design of the DX3 transmitter provides a feel that any driver will appreciate. Its overall low weight allows all-day driving with minimal fatigue. The control layout is amazingly intuitive the servo reversing switches, steering and throttle trim dials, AVC/steering rate dial and 3-position throttle limiter are all perfectly positioned to be quickly accessible when needed and out of the way when not in use. An easy to grip, foam-covered steering wheel also contributes to exceptional comfort and precise control that all surface modelers will enjoy. DSMR® TECHNOLOGYThe DX3 transmitter is built around proven Spektrum DSMR® 2.4GHz frequency-agile technology. The range and response of DSMR technology is outstanding, particularly in noisy 2.4GHz environments. It can used with any surface application and is backwards-compatible with Spektrum DSM2® receivers. AVC® (ACTIVE VEHICLE CONTROL®)The DX3 radio system supports the on-demand traction control of Spektrum AVC® (Active Vehicle Control®) technology. With an AVC® system, you can dial in extra stability as needed to carve corners or nail jumps without backing off the power. You have full-throttle freedom over rough terrain, slick surfaces and loose dirt. When you don't want the extra traction, just dial back the stability and get loose. The DX3 transmitter's AVC system works behind the scenes, making hundreds of minute steering and throttle adjustments per second to keep you precisely on the line you want to hold. SMART BATTERY LEVEL INDICATOR AND ALARMIntegrated into the face of the DX3 Smart is a helpful Smart Battery voltage indicator. Drivers can easily find out the charge of their Smart battery with a quick glance and once the battery level gets low, an alarm will sound.(Smart ESC, Smart Battery and Smart compatible receiver required)Contents:1 piece

€109.99*

Average rating of 0 out of 5 stars

60130/02 FG Rear spoiler black, 1pce.
Item N° 60130/02Rear spoiler black, 1pce.Solid and impact-resistant rear spoiler in black. Suitable for the Off-Road buggies Leopard 2, Leopard 4, FG Off-Road Buggy and FG Marder.

€23.90*

Similar products

Average rating of 0 out of 5 stars

60210/06 FG Off-Road Buggy tires M wide glued, black
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim black. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€107.95*

Average rating of 0 out of 5 stars

GWH71 GRP 1:6 Buggy "BULDOG" tire glued, 18 mm square, 2 pcs.
grp_w71 Rubber compund: Extra Soft - GWH71X
Item N° GWH71 GRP 1:6 Buggy "BULDOG" tire glued, 2 pcs.medium aggressive knobby treadgood directional stabilitygood lateral tractiongood propulsionfor solid surfacesTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.

€45.60*

Average rating of 0 out of 5 stars

6406/05 FG Off-Road tires Killer Soft glued - 2pcs.
Item N° 6406/05 Off-Road tires Killer Soft glued - 2pcs.The Killer tires are glued on genuine 1/6 scale FG buggy rims with extension ring! Suitable for all 1:6 Off-Road models, Monster and Stadium Trucks. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.This Killer tire is distinguished through a lot of grip and a long durability. Diameter x width: 165 x 65 mm Rim with 18 mm square drive

€64.70*

Average rating of 0 out of 5 stars

60215/05, FG Tire Off-Road Buggy M narrow glued
Narrow Off-Road Buggy tires 60 mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y0067. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing () if necessary is unavoidable.Diameter: 180 mmWidth: 60 mmContents:2 pieces

€89.90*

Average rating of 0 out of 5 stars

60210/05 FG Tire Off-Road Buggy M wide glued
Genuine FG spare/option part. Wide Off-Road Buggy tires 80mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y6106/01. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 180 mmWidth: 80 mmContent:2 pieces

€107.95*

Average rating of 0 out of 5 stars

60215/06 FG Off-Road Buggy tires M narrow glued, black
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim black. Outer Ø 175 mm, width 65 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€89.90*

Average rating of 0 out of 5 stars

60214/05, FG Tire Off-Road Buggy S narrow glued, 2 pcs.
Narrow Off-Road Buggy tires 65 mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y0067. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing () if necessary is unavoidable.Durchmesser x Breite / diameter x width 180 x 60 mm

€89.90*

Average rating of 0 out of 5 stars

60209/05, FG Tire Off-Road Buggy S wide glued
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim white. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces

€107.95*

Average rating of 0 out of 5 stars

GWK71 GRP 1:6 Buggy "BULDOG" tire glued on yellow rims, 18mm square, 2 pcs.
grp_gwk71b Rubber compund: Soft - GWK71A
Item N° GWK71 GRP 1:6 Buggy "BULDOG" tire glued on yellow rims, 2 pcs.- medium aggressive knobby tread - good directional stability - good lateral traction - good propulsion - for solid surfacesTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.

€45.60*

Average rating of 0 out of 5 stars

6405/05 FG Off-Road tires Killer Medium glued
Genuine FG spare/option part. The Killer tires are glued on genuine 1/6 scale FG buggy rims with extension ring! Suitable for all 1:6 Off-Road models, Monster and Stadium Trucks. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.This Killer tire is distinguished through a lot of grip and a long durability. Diameter x width: 165 x 65 mm.Rim with 18 mm square drive.Content:2 pieces

€64.70*

Average rating of 0 out of 5 stars

y1402/01 MadMax CROSS BOND 170x80/x60 tires for FG/Smartech and other (18 mm square drive)
CROSS BOND 170 x 80 mm and 170 x 60 mm tires mit MadMax Extreme 20 bolt-beadlock rims with 18 mm wheel square and reinforced beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 18 mm square wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

€119.90*

Average rating of 0 out of 5 stars

6231/07 FG Stadium-Truck tires S glued, chrome rims, 18 mm - 2pcs.
The new Stadium Truck tires S are characterized by a lot of grip and stability in curves. This was achieved through a newly developped, softer rubber mixture. The tires are glued on Stadium chrome rims. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.These Stadium tires have a bigger square depth, this reduces a cylindrical turning of the square wheel significantly. To mount these tires you need a 18 mm square wheel driver.Durchmesser x Breite / diameter x width 170 x 90 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapter

€112.50*

Customers also viewed

Average rating of 0 out of 5 stars

FG Leopard 4 Electric, 4WD
No matter where you will set this model into action - you will always be right in front with the FG Leopard 4E! The E stands for electric power, the 4 means fourwheel drive. Extremely fast, terrific torque and all this without any engine noise. The Leopard 4E is equipped with a powerful brushless engine and a engine control.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Empfänger: Mini BECy1570 CYS S0650 Largescale servo, 40 kg/0,11 secTx-batterys 4 pieces y0660/04 Equipment: y1567 ZTW Beast Pro 200A ESC TT56112/700 Top Tuning Monster Brushless Motor 700 kV The control can be regulated simply via transmitter or optionally via a program card. For the final assembling you need LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length of 150mm and a width of 50mm. The model is delivered with the EC8 connector system.

From €1,279.90*

Average rating of 0 out of 5 stars

Ball bearings for FG, sealed, diverse sizes
lager_0003 Size: y19611 For wheel bearing, 2 pieces
Genuine HT spare/option part. Dimensions:Alloy differentials 15 x 28 x 7 mmPlastic differentials 12 x 28 x 8 mmClutch bell(except standard Formula 1) 10 x 22 x 6 mmLayshaft 10 x 19 x 7 mm Wheel bearing 8 x 22 x 7 mmContents:1 pair / 2 pieces

€10.70*

Average rating of 0 out of 5 stars

y0580 Mammoth Supergrip for 1/6 and 1/5 offroad cars glued
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

€119.90*

Average rating of 0 out of 5 stars

y0760 BigScale Rallye-Cross tires Typ 450 for FG and other, 2 pair/4 pcs. for 18mm square
Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter

€69.90*

Average rating of 0 out of 5 stars

6419/09 FG Slick tires rear S1/80mm 1:6 glued, 2 pcs.
Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Measures:Diameter: 145 mmWidth: 80 mmRim with 18 mm square drive.

€118.95*

Average rating of 0 out of 5 stars

y1189 Stadium wheels on disc rim, 2 pairs
Complete set of four CRT stadium tires and rims, mounted and glued with tire inserts. Fits FG and Carson 1/6 scale cars.Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Also suitable for:With the following wheel adapter: y1183 Rim adapter

€99.90*

Average rating of 0 out of 5 stars

8523 FG Rear shock absorber set long - 2pcs.
Shock absorber conversion kit for all 1:5 and 1:6 Ecoline models. Bulk oil-pressure shock absorber Ø20mm, experienced for years. The set contains 2 shock absorber with spring plate and spacer rings.

€55.00*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency