y1415 Version:
y1415/02 One pair for approx. 80 mm wide tires with 18 mm Square
New highly reinforced MadMax rim with 18 mm square drive and optimized beadlock rings.20-fold screwed very tough and suitable for all 1/6 &1/5 FG, Smartech and many more.The MadMax Extreme rims are available for either 60 or 80 mm tire width.They come with optimized inner and outer beadlock rings, 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench) and reinforcement rings around the wheel hex.Our shop offers you the choice of economically priced sets of the following combinations:y1415/01 one pair for approx. 60 mm wide tiresy1415/02 one pair for approx. 80 mm wide tiresy1415/03 one pair each for approx. 60 and 80 mm wide tires
y0529_01 Version:
y0529/01R One piece right hand thread
Steel ball joint 4 mm r/h or l/h thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread
GRP tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!New structure conceptIn the new line of tyres, the Belt, Insert an Wheel have also been improved to further improve performance in every race situation and at any temperature of use. Vulcanized Beld with new specific weaves angles. Insert with new variable deformation foam material. Wheel made by Dupont (R) plastc material resistant to high temperatures and flexible at low temperatures.Extraordinary GripThe new tyres of this line provide an incredible Durability even on abrasive asphalt tracks, where the previous compounds lasted less.The difference in Duration is very big with an increase of 35%.Incredible DurationThe new tyres of this line provide an incredible Durability even on abrasive asphalt tracks, where the previous compunds lasted less.The difference in Duration is very big with an increase of 35%.Regularity and PerformanceThe new tyres of this line provide Regularity of abolute performance with each subsequent use, compared to competing tyres.The difference is very big because Performance remains 100% even with each subsequent use, and remains 100% until the tyres is finished. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square driveContent2 pieces / 1 pair
Genuine FG spare/option part.Steel taper disks, 3.5 mm thick, with a higher stiffness compared to alloy taper disks. Installation of these disks allows for larger operation angles of the metal ball joints and rose joints. You need two disks per joint.Contents:4 pieces
Genuine FG spare/option part.Strong, maintenance-free and backlash-free precision ball joints made of aluminum. Ball with 5mm bore and body with M6 r/h female thread. For use with the adjustable upper aluminum and plastic wishbones at front and rear suspension.Comes with the required conical spacers included.
Genuine FG spare/option part. Steel ball-and-socket-joint with 5mm bore in the ball and M6 right-handed thread for use with the wishbones. For the installation are needed the adjusting screws 4430 or 4431. The delivery contains all needed pin disks. Dimensions:A = 5 mmB = M6C = 8 mmD = 15.5 mmE = 37 mmContents:2 pieces
Alloy ball-and-socket joint with 5mm bore in the ball and M8 right-hand thread for use with wishbones.When using these ball joints you will get a weight reduction in comparison with,A = 5 mmB = M8C = 8 mmD = 17.5 mmE = 39 mm