Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

2012/504 Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution

Product information "2012/504 Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution"

Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution.

Suitable for all servos with an output shaft with 25T spline shaft, for example:
  • y2006 Digital Big-Scale Servo D-21HV
  • Nearly all Robbe/Futaba servos
  • Mega Power servo
  • Thunder Tiger DS1015
  • Savöx servos
  • and many more!


Content:
  • 1 x y0700 Double sided alloy servo horn
  • 1 x y0700/01 Single-sided alloy servo horn
  • 2 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/510 (one spacer drilled to 3 mm inner diameter)
  • 1 x M3 x 30 mm Screw
  • 2 x M3 x 12 mm Nut

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Alternatives

Average rating of 0 out of 5 stars

2012/500 Linkage set dedicated to Mecatech FW01, complete
Complete set for steering, throttle and brake linkagesSet includes:3 x 6534/02 Throttle pivot post for 2 mm linkages 1 x y0132 y0132 Linkage rod for MecaTech brakes1 x 1213/10 Steel ball 7 x 6,5 mm1 x 66244, Ball joint 7mm M41 x 1213/11 Steering linkage l./r., M4 x 42mm1 x 6020 Set collar 2,1mm1 x 1018/01 Throttle linkage Evo 09 / Comp. 077 x Nut M32 x Screw M3 x 16 mm3 x Screw M3 x 18 mm 2012/501 Throttle linkage 2012/502 Brake linkage set 2012/503 Steering servo linkage set 2012/504 Throttle/brake servo horn The Servo arm is suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!

€79.90*

Customers also bought

Average rating of 0 out of 5 stars

y0700/01 Single-sided alloy servoarm, 1 pce.
Item N° y0700/01 Single-sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.

€13.90*

Average rating of 0 out of 5 stars

6534/02 FG Throttle pivot post
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.

€8.50*

Average rating of 0 out of 5 stars

8018 FG Throttle rod set for Zenoah 1:5
For touring car. With 2 mm thick and 350 mm in the lenght.

€10.50*

Average rating of 0 out of 5 stars

2012-259 Mecatech Titanium Front Anti-Roll Bar
Genuine Mecatech spare/option part for the FW01.Contents:1 pieces

€27.00*
%

Average rating of 0 out of 5 stars

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines
Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.40* €4.90* (10.2% saved)

Average rating of 0 out of 5 stars

y0700 Double sided alloy servoarm, 1 pce.
Item N° y0700 Double sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.

€12.90*

Customers also viewed

Average rating of 0 out of 5 stars

2012/500 Linkage set dedicated to Mecatech FW01, complete
Complete set for steering, throttle and brake linkagesSet includes:3 x 6534/02 Throttle pivot post for 2 mm linkages 1 x y0132 y0132 Linkage rod for MecaTech brakes1 x 1213/10 Steel ball 7 x 6,5 mm1 x 66244, Ball joint 7mm M41 x 1213/11 Steering linkage l./r., M4 x 42mm1 x 6020 Set collar 2,1mm1 x 1018/01 Throttle linkage Evo 09 / Comp. 077 x Nut M32 x Screw M3 x 16 mm3 x Screw M3 x 18 mm 2012/501 Throttle linkage 2012/502 Brake linkage set 2012/503 Steering servo linkage set 2012/504 Throttle/brake servo horn The Servo arm is suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!

€79.90*

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Average rating of 0 out of 5 stars

Samba MOCA Cruze 1/5 TC bodyshell clear 1mm
Genuine Samba spare/option part. The body shell is neither cut nor drilled, clear and can therefore be adopted to all touring cars with a 530/535 mm wheelbase.We have decided to make a new TC bodyshell to offer a new car from the WTTC series for the 5th scale drivers.Currently the most sought after large scale body shell with optimal aerodynamicsMaterial thickness 1 mm. The body shell consists of one part.Precut, the final cutting must be made according to the chassis you use it on.Width front / rear: 392 mm.Contents:1 piece

€89.90*

Average rating of 0 out of 5 stars

y1046 Clemps for hydraulic brake lining 4 mm
Genuine rc-car-online spare/option part. Clemps for hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Contents:8 pieces with mounting screws

€9.50*

Average rating of 0 out of 5 stars

y1309 All steel linkage for steering servo/servo saver application
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

FG Formula 1 Sportsline
Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!

€1,299.00*
%

Average rating of 0 out of 5 stars

05.19.06 OSKART Steering Linkage M5
Genuine OSKART Steering Linkage spare/option part.Fits 1/2 scale OSKART.Contents:2 pieces

€21.00* €42.00* (50% saved)
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Plugin Development