y1379 Pinion fastening set with nut for Losi 5ive-T/2.0 and Mini
Product information "y1379 Pinion fastening set with nut for Losi 5ive-T/2.0 and Mini"
This set allows for fastening the pinion to the clutch bell utilizing a full metal self locking nut when using our gas-nitrided clutch bell y0726.
The screw will be fully inserted into the clutch bell from the backside using high strength thread locking compound.
This setup provides a couple of significant advantages:
Set includes:
The screw will be fully inserted into the clutch bell from the backside using high strength thread locking compound.
This setup provides a couple of significant advantages:
- This self locking nut does not use the usual plastic insert; therefore it is completely temperature resistant!
- Theres no need to wait for the thread locking compound to cure after a pinion change; the connection is safe and ready to use immediately. For safety reasons nut and spring lock washers should only be used once.
- No need to worry about worn-out Allen screw heads.
- In case the screw ever breaks at the point where it enters the pinion, it can still be removed with ordinary tools. Theres still the like new screw head inside the clutch bell ready for screw removal.
Set includes:
- 2 pieces of high strength 12.9 grade screws
- 10 pieces of full metal self locking nuts
- 10 pieces of spring lock washers
Login
Accessories / Spare parts
Refill pack for y1379. Set includes:20 pieces of full metal self locking nuts20 pieces of spring lock washers
Customers also viewed
gpm_slo5t Teeth:
SLO5T018T - 18 teeth
Hardened steel pinion set for Losi 5ive-T, 5ive-B and Mini, with corresponding engine mount inserts included. All parts with laser etched tooth count.Please note: The pinion do fit the 5ive-T 2.0 as well, of course. However, you then have to use the 5ive-T 2.0 engine mount inserts of the appropriate tooth count, inserts from the 5ive-T do not fit! Available with 16, 18T/20T/21T. The 19T pinion is stock equipment in Losi 5ive-T and Mini, 20T is stock in the 5ive-B.The 16T pinion is profile shifted and has the same dimensions as a normal 18T pinion.It is specially made for vehicles where the stock tires are replaced by much larger diameter rubber (i.e. monster truck tires and MadMax Giant Grip).Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.SLO5T018T replaces LOSB5046 and LOSB5805SLO5T019T replaces LOSB5044 and LOSB5801SLO5T020T replaces LOSB5045 and LOSB5802The higher the tooth count, the higher the top speed!
This reed valve system converts a normal piston-port engine into a reed valve engine. It offers the advantage of increased intake duration for a better charge for more power. As a positive side effect no fresh gas loss occurs during the downward movement of the piston because the membranes close this path.The reed valve block replaces the usual stock insulator. To use the advantage of the reed system, it is necessary to modify the piston skirt on the intake side. Depending on the engine it is advantageous for best results, to slightly match the cylinders intake port to the Epoxy insulator plate at the bottom of the reed valve system. Both steps are described in the installation instructions for Zenoah and Chung Yang engines. Our thanks for these instructions go to our customer Thomas Hoenicke.Note: For the time being the epoxy insulator plate must be slightly reworked to fit a G320 Zenoah engine. The manual has been written with the conversion of a G320, the affected area for modification is therefore shown.The unit is 24.5 mm high.