y0945 HT-Alloy gear plate for Gas/Hell Devil/CRT 4x4/Thunderbolt / Smartech Titan

rc-car-online

€39.90*

Prices incl. VAT plus shipping costs

Available

Product number: y0945

EAN: 4058575019329

Product information "y0945 HT-Alloy gear plate for Gas/Hell Devil/CRT 4x4/Thunderbolt / Smartech Titan"

Genuine HT spare/option part.

Gear plate, surface deburred with vibratory grinder.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

s054320/01 Brake pads for Smartech tuning brake, 4 St

Item-No.: s054320/01Brake pads for Smartech tuning brake

€19.90*

HT Aluminum differential case conversion kit Carson Gas/Hell Devil/CRT 4x4/Thunderbolt, y0928, set

Alloy case conversion kit for Carson Gas Devil 4x4 (Smartech Titan) only, can be used for all differentials.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.

€89.90*

s054320, Smartech tuning brake Gas/Hell Devil/CRT 4x4/Thunderbolt / Titan, set

Set includes 2 rotors, 4 brake pads and 4 return springs. The steel rotors will last significantly longer on the differential drive cups, wear between rotors and brake pads is reduced as well.

€49.90*

y0968 HT-Steel pinion 34 teeth Speedgear for Carson / Smartech 4WD cars

Genuine HT spare/option part. Nitrited steel spur gear, profile regraded, for combination with the stock 43T spur gear which goes on the clutch bell. This gives a numerically lower drive ratio and makes it possible to use standard diameter buggy tires on this car!Attention: The speedgear has the same diameter as the stock 37T gear and is therefore not compatible with the other 37T/40T HT tuning gears!Speedgear 34T: I=7,74Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.Contents:1 piece

€44.90*

HT-Steel pinion for Carson / Smartech 4WD cars

ritzel_gas_devil Size: y0345 - Set with 37 teeth and 40 teeth+ 44.9EUR

Genuine HT spare/option part. Nitrited steel gears, fit Carson Gas Devil / Smartech Thunderbolt 4x4 only.These gears are available with 37T or 40T, both share the same diameter and must be used in combination.Please note: the gears cannot be used in combination with the stock gears and the 37T version is no replacement for the stock 37T gear!This gives you the following new gear ratios:I=10.58I=9.79 (when using two identical gears !)I=9.06The stock gear ratio is I=11.38 and I=8.42 is possible by switching the gears.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

Variants from €44.90*

€89.80*

y0929 HT Aluminum limited slip differential conversion kit for Carson Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan

Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece

€129.90*

Customers also viewed

7088 FG Volume compensation for shock absorber

Genuine FG spare/option part. Ersatzteil zu:7083 FG Shock absorbers 97 short complete7200 FG alloy shock absorber 04 short7201 FG Alloy shock absorber 04 medium-short 7202 FG alloy shock absorber 04 medium-long 7203 FG alloy shock absorber 04 medium7204 FG alloy shock absorber 04 long Content:Two pieces

€4.70*

y1135 Alloy gear plate for Carson / Smartech C6

Genuine HT spare/option part.Fits all Carson / Smartech 2WD buggy and monster cars like UNOMonster Truck AttackSuper AttackAttack EvoComancheCRT, CPTGas Blaster...The brake cam bushings are replaceable.Contents:1 piece

€69.90*

%

TT1030 Top Tuning CAR-STAND for 1/5, 1/6, 1/8, 1/10

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

€179.90* €199.90* (10.01% saved)

Configure now

s23006, Crankshaft PT23/28, set

With crank key included.

€59.90*