y1042 Angle connector 45° for hydraulic brakes - 1 pce

rc-car-online

€12.90*

Prices incl. VAT plus shipping costs

Currently unavailable

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Product number: y1042

EAN: 4058575021162

Product information "y1042 Angle connector 45° for hydraulic brakes - 1 pce"

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

Connecting thread M5

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

y1358 PTFE thread sealing tape, 12 mm wide, 10 m roll

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters

€2.90*

Customers also bought

3000-24 Mecatech Brakedisk steel/epoxy

mec_3000_24 Material: Epoxy

Genuine Mecatech spare/option part. Replacement part for Mecatech Cross Hydro. Epoxy or steel to choiser.Dimensions: Strength: 1,5 mm Outside diameter: 64 mmContent:1 piece

€9.90*

5476/01 Mielke HR Wheel nuts M8

Mielke wheel nuts for 8 mm axles!

€29.00*

y1613 Mammoth Supergrip mounted and glued on silver FG rims

y1613 Version: Front Supersoft und Heck Supersoft+ 60EUR

Genuine rc-car-online spare/option part.The optimal parking lot or race tires for your FG Racetruck model.Type Width Outer diameterFront 64 mm 153 mmRear 78 mm 153 mmGlued on original FG-Racetruck rims (rear tire with extension to the inside), incl. foam rubber insert,FG rim with 18 mm square drive and reinforcement ring.Attention: From experience we warn against using rims and extensions from another manufacturer.Since the Mammoth tires provide a very good grip, the rim and bonding are extremely stressed. Due to the high torque load in relation to the bonding of tires on large models, an occasional check in this regard and possibly a repair of the bonding (y0067) is inevitable.As a recommendation:The dirtier the track or the colder the temperature, the softer the rear tire should be.Reference for the front tire: With 2WD models this should be one to two stages harder than the used rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is often good to drive.Of course, with Mammoth Supergrip Racetruck tires, the softer the tire, the higher the wear.The Mammoth Supergrip Racetruck tires have a special onroad tread. Whereby these still have an optimal grip after the wear of the tread, and can still be driven for a long time.

Variants from €89.90*

€149.90*

y1041 Angle connector 90° for hydraulic brakes - 1 pce

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€12.90*

y1040 T-connector for hydr. brake system - 1 pce

T-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

y1046 Clemps for hydraulic brake lining 4 mm

Genuine rc-car-online spare/option part. Clemps for hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Contents:8 pieces with mounting screws

€9.50*

Similar products

y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€14.95*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

y1045 hydraulic brake lining 4mm - 1 St

hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Length: 1 meterDimensions:Inner diameter: 2 mmOuter diameter: 4 mm

€4.90*

y1041 Angle connector 90° for hydraulic brakes - 1 pce

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€12.90*

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

y1043 connector straight for hydraulic brakes - 1 pce

connector straight for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€8.90*

y1040 T-connector for hydr. brake system - 1 pce

T-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

y1337 Epoxy P-R-M Race brake discs for FG / Smartech / Carson

Top quality epoxy P-R-M Race brake discs with 10 dirt slots for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)! The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218). The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.1 pair (2 pieces) Dimensions: Outer diameter: 60 mm Thickness: 2 mmsocket for 18 mm square wheel drive

€22.90*

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

y1046 Clemps for hydraulic brake lining 4 mm

Genuine rc-car-online spare/option part. Clemps for hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Contents:8 pieces with mounting screws

€9.50*

y1044 Y-connector for hydr. brake system - 1 pce

Y-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

y1042/01 Angle connector with adaptor 45° for hydraulic brakes

Angle connector for all hydraulic brake linings with a outside diammeter of 4 mm. e.g Colari, Magura II and Mecatech.

€12.90*