y0722 Axle plugs for Losi 5ive-T/2.0, Mini

Genuine ATOP spare/option part. Upper rear camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 140 mm. Contents:2 pieces

Genuine HT spare/option part. The spool replaces the center differential and keeps the speed of both output shafts the same. As a result, especially the acceleration of the vehicle is significantly increased.The spool is nicely made of high-quality burnished steel and very strong. Its total length is the same as a normal differential housing with gasket. The gasket is no longer used with the spool. The driving pin of the front output shaft is secured by an O-ring. The screws for the connection with the spur gear are secured with nylock nuts. This eliminates the need for waiting for the curing of a thread locking compound and makes the removal of screws with damaged head much less critical.The spool would physically fit front and rear applications as well; however, its use here makes no sense to driving dynamics.Scope of delivery:Spool2 x Driving pin 4 x 20 mmO-ring4 x Steel nylock nut M4

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!

Complete set of screws, nuts and washers for HPI Baja 1/5 vehicles.The set includes a total of 434 screws, nuts and washers in different quantities which are all used on HPI Baja 1/5 vehicles and Carson 1:5 Wild GP Attack.11 sizes of cap head screws9 sizes of CSH screws10 sizes of button head screws4 sizes of set screws2 sizes of washers3 sizes of lock washers3 sizes of self-locking nuts2 sizes of nuts with serrated flange2 sizes of flanged self tapping screwsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:20 piecesM3x126 piecesM3x4510 piecesM4x612 piecesM4x1212 piecesM4x2510 piecesM4x306 piecesM4x507 piecesM5x206 piecesM5x306 piecesM5x356 piecesM6x25CSH screws in 10.9:10 piecesM3x2010 piecesM4x1019 piecesM5x1616 piecesM5x206 piecesM5x302 piecesM5x407 piecesM6x14Button head screws in 10.94 piecesM3x1610 piecesM3x303 piecesM4x166 piecesM5x123 piecesM5x302 piecesM5x356 piecesM5x406 piecesM5x452 piecesM6x306 piecesM6x30Grub screws:6 piecesM3x39 piecesM4x46 piecesM4x124 piecesM6x45Washers in Din125:10 pieces3,2x6,8x0,512 pieces4,3x8,7x0,8Safety washers:20 piecesM420 piecesM520 piecesM6Self-locking nuts:10 piecesM310 piecesM415 piecesM5Flanged nuts with serrated base:21 piecesM410 piecesM5CSH screws Torx:10 piecesM4x15 (4,2x16)10 piecesM4x18 (4,2x19)Schneidschrauben Torx mit flanged:10 piecesM2,6x1012 piecesM3x10

Genuine Losi spare/option part.CNC-machined from 6061-T6 aluminum by Area RC.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: 85 grams.Content:1 piece

Genuine Atop spare/option part. Colored fuel hose with clams and suction tubesArea Rc High flow fuel line kit.This high flow fuel line kit fits the HPI Baja series and the Losi 5ive-T/B and Mini. It may fit other large scale cars as well.The kit comes with 6 pieces of fuel line clips and 2 assembled plastic fittings. Those fittings cannot be compressed by the tanks fuel line grommet, so the inner diameter remains constant which improves fuel delivery to the carb.Fuel line dimensions:Length: 1mInside diameter: 3 mmOuter diameter: 6 mmAvailable colors: AT001/01 - YellowAT001/02 - RedAT001/03 - BlueAT001/05 - GreenIncludes:2 x Assembled plastic fittings6 x Fuel line clipsTygon fuel line