22 products found for "y1350"
Catalogue #1
Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece
y1351 Version:
y1351/03 Complete set+ 149EUR
Genuine HT spare/option part. A must-have for 1/5 on-road racing! Even though it looks funny at first sight for uninitiated people! ;-) Just like in full-size racing our tires need a certain temperature to provide the necessary grip that is needed to achieve good lap times. Usually this means that the car will get really fast times only after a few laps. The driver who uses preheated tires has a considerably advantage. With cold outside temperatures or low grip tracks, like a not so clean parking lot, it often not possible at all to bring the tire temperature up to the required range just by driving. As a result the car will be difficult to control! Measures:maximum outer diameter of 130 mm maximum tire width of 80 mmThat includes all standard 1/5 touring car tires! ( ) Instructions: The tire warmers may be operated only on 12 to 13.8 volts AC or DC. In order to reach optimum operating temperature, a power supply with a 12 - 13.8 volts AC or DC and at least 10 amps output power should be used. The T2m Powerbase y1352 is the perfect solution for this application. The operation of the tire warmers directly from a 12 volt car battery (without Powerbase) is also possible, of course. In order to prevent damaging the filament inside the blanket, they must not be bent and not used without tires!Contents:1 set
Variants from €99.90*
y1353 Version:
y1353/01 Battery Box with BEC connector
This black plastic battery box accepts 4 AA cells, available with either BEC or universal connector.The universal connector version is also available with receiver switch.UniversalBEC
Ideal power supply for tire warmers! The Powerbase power supply delivers with 13.8 volts the ideal and constant current for tire warmers. A 45 mm cooling fan on the back keeps the Powerbase power supply running cool. Including a slow 4 A / 250v fuse for overload protection. Specifications: Input voltage: 190 - 240 Volts AC Output voltage: 13.8 volts regulated DCOutput connector: 4 mm plug / alligator clips For additional information pleas go to the Technical data tab. Tire warmers can be found under part numbers y1351/01 and y1351/02 or save with the complete set part number y1351/03.Contents:1 piece
y1354 Version:
y1354/02 SPEED TEC Race
Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm
Genuine Speed-Tec spare/option part. SPEED TEC tuning insulator, slanted. Especially for 1/5 & 1/6 offroad cars The slanteded version is required for many offroad cars when installing a taller insulator and for HPI Baja series cars in general. The material components of this high quality engineering plastic, with an extremely high melting point of 280° C, guarantee optimal heat dissipation. Unlike the original insulator, this allows for a much better thermal insulation of the carburetor and therefore prevents fuel vapor lock in the carburetor at high ambient temperatures! The leaning out of the engine at higher temperatures is counteracted! The increased height and optimized port allows for lower fuel consumption!Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets.Please notice: the cylinder shroud y1016/021 must be reworked for angled tuning insulator!Dimensions:Height of aluminum intake 15 until 23 mmHeight of insulator plate: 6 mm Set includes: Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm
Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters
Genuine HT spare/option part. Stainless steel protractor with 200 mm leg for angles up to 180°. Well-suited for measuring of camber or toe--in/toe-out on rc cars.Contents:1 piece
y1530 Size:
y1530/100 -100 ml+ 5EUR
Genuine HT spare/option part. Differential oil, suitable for Lightscale Smooth, SCS and Mecatech differentials. Specially designed for grippy tracks. The differential oil provides a good locking effect combined with very good traction.Contents:1 piece / 50 ml / 100 ml
Variants from €7.90*
3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.
federn_dirt_gd Version:
y0350/04 GD04 short, blue
Genuine HT spare/option part. Fits Carson Gas Devil/ Hell Devil 4x4. Not for Thunderbolt!.Measures:Inna diameter: 31,4 mmOuter diameter: 37 mmLength short spring: 103 mmCoils short spring: 8 StückLength long spring: 143 mmCoils long spring: 10 StückFront axle:VersionMeasuresColorItem N°GD012.3 x 103 mmyellowy0350/01GD022.4 x 103 mmredy0350/02GD032.6 x 103 mmbrowny0350/03GD042.75 x 103 mmbluey0350/04GD052.8 x 103 mmsilvery0350/05GD062.9 x 103 mmblacky0350/06Rear axle::VersionMeasuresColorItem N°GD072.3 x 143 mmyellowy0350/07GD082.4 x 143 mmredy0350/08GD092.6 x 143 mmbrowny0350/09GD102.75 x 143 mmbluey0350/10GD112.8 x 143 mmsilvery0350/11GD122.9 x 143 mmblacky0350/12HelpThe stock springs have 2.5 mm wire diameter. The Gas Devil / Titan shocks are factiry filled with silicone oil 500, which is slightly soft in rear and way to soft in front. In rear brown springs with oil in the 800 - 900 range or blue springs with 900 - 1000 range oil should be fine for bashing. In front blue springs and 1500 silicone oil are a good point to start from. Due to the size of the shocks you need two bottles of oil pes axle.Contents:2 pieces
Genuine ZTW spare/option part. For programming the ZTW Beast Pro 300A 12S ESC and 200A 8S ESC as well as for connection to a PC and for firmware updates of the esc.The Gecko software from ZTW on the PC is required for this: Specification:Length: 91 mmWidth: 54 mmHeight: 18 mmWeight: 68gPower supply: DC 5.0V - 12.0VContents:1 piece
Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey
Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)
Fits Area 5ive-T clutch bell holder AREA-5T-009. Both sides sealed (2RS) for increased dirt resistance. Does not fit stock parts!Content:Two pieces
y1340_09 Dekorvariante:
y1340/09 Dekor zu Desert Buggy XL Heckspoiler
Decal especially for Desert Buggy XL rear wing.Dimensions:250 x 100 mm
Race ported top end set for Zenoah G320 engine.The SPEED TEC EXPERT genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intakeTransfer port covers:Glued and ready for use Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome groundSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().
Rc-car LiPo hardcase battery with XH balancer connector and cable with T-connector (link to the T-connector). Battery conector:Typical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesCan be charged with 5C when time is criticalRecommended charge with 2 3CPArt numberLiPo-Battery typeCable cross sectionCaseCapacity mAhVoltWidth +/- 1,5 mmHeight +/- 1,5 mmLength +/- 5 mmWeight +/- 10gCont. currentPeak currenty1300/023 S / 2 P12AWG/3,3hart6.00011,138,046,5137,546240C(240A)80C(480A)y1300/034 S / 2 P12AWG/3,3hart5.50014,848,046,5137,555840C(220A)80C(440A)y1300/046 S / 1 P10AGW/5,27soft5.20022,248,046,0155,070845C(189A)90C(378A)y1300/063 S / 2 P10AWG/5,27soft6.00011,144,033,0137,042440C(240A)80C(480A)
Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal
Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. Both are available as an option from our shopping cart menu. Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
