AT-DBXL02 ATOP aluminum front top chassis brace for Losi DBXL 2.0

€39.90*

Available

Product number: at_dbxl032

EAN: 4058575148746

Product information "AT-DBXL02 ATOP aluminum front top chassis brace for Losi DBXL 2.0"

Genuine ATOP spare/option part.

CNC-machined 6061-T6 aluminum front top chassis brace; fits Losi DBXL 2.0.

Stiffer than the stock plastic part (from set # LOS251115), the aluminum brace reduces chassis tweak in the area of the steering assy.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

AT-DBXL029/030/031 ATOP Front- and rear chassis braces, full set, for Losi DBXL 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.Contents:1 piece

€109.90*

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

R404SBS Futaba Receiver 2,4GHz

With the Futaba R404SBS, Futaba offers the fastest and most compact receiver for RC cars and boats on the market today! The R404SBS has the ultra-fast signal transmission F-4G (10 channels with telemetry at maximum transmission speed). This makes the model's response even more direct while maintaining maximum transmission reliability!The new F-4G (Futaba 4th Generation System) transmission mode supports the familiar SR mode and has an even higher transmission speed than the previous T-FHSS SR. At the same time, the size of the new F-4G receivers R404SBS / R404SBS-E could be reduced again. To make this possible, the R404SBS-E has a large, upward-pointing antenna to optimize signal reception. Due to the chosen design, the footprint of the receiver remains unchanged.To take full advantage of the speed of Futaba's F-4G SR technology, there are numerous FUTABA SV servos that can also be converted to SR mode. The following servos are currently SR compatible: BLS371SV, BLS471SV, BLS571SV, BLS671SV, BLS671SVi, BLS373SV, S9372SV, S9373SV, HPS CB700, HPS CT700, HPS CB500, HPS CT500.The R404SBS has antenna diversity. The receiver constantly compares which antenna has the better signal and switches to it in a flash. The R404SBS has the second antenna in the housing.S.BUS2 sensors can be connected to the S.BUS2 port. They transmit up to 32 telemetry data sets. The receiver has an integrated telemetry transmitter that transmits the data to the transmitter. This allows the measured values to be displayed or acoustically output at the transmitter.ATTENTION: The receiver supports HV (High Voltage) and can be powered directly from a 2s LiPo battery. Always make sure that the connected servos are also designed for HV! Technical specifications Transmission type: F-4G Frequency range: 2.4 GHz Channels: 4 PWM / 10 S.BUS Transmission power: 100 mW EIRP S.BUS Port: S.BUS2 Voltage range: 3.7-8.4V Dimensions: 25.5 x 20 x 10.6mm Weight: 5.7g Features 4/10 channel F-4G receiver 10 channels of telemetry at maximum transmission speed SR mode compatible Telemetry with S.BUS2 Telemetry with 32 channels S.BUS2 port Hi-Voltage (HV) Antenna diversity

€95.00*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€47.90*

y1350 Aluminum engine mount for Losi DBXL, reinforced version

Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece

€14.90* €34.90* (57.31% saved)

Similar products

DBXL024 ATOP Aluminum axle extenders all Losi DBXL / DBXL-E / 2.0 / MTXL, with closed nuts

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC.Increases track width by 25 mm. Fits all versions of DBXL / DBXL-E / 2.0 (brushless and gas) and MTXL. 2 mm O-rings protect against drive pin loss.Set of four including O-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

€64.90*

Details

AT-DBXL002 ATOP aluminum camber rods/steering rods for Losi DBXL/DBXL-E

Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces

€34.90*

Details

AT-DBXL026/027 ATOP Aluminum front spindles for all Losi DBXL/MTXL

Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces

€149.90*

AT-DBXL001 ATOP Alloy spring retainer for Losi DBXL/XL-E +MTXL shocks

Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces

From €16.90*

Details

AT-DBXL002/01 ATOP Spacer bushings for camber/steering rods of Losi DBXL and DBXL-E

Genuine ATOP spare/option part. Aluminum spacer bushings for the ball joints on camber and steering rods of Losi DBXL and DBXL-E.Content:8 pieces

€9.80*

AT-DBXL020 ATOP Complete Aluminum transmission case front / rear for Losi DBXL/DBXL-E/2.0 + MTXL

Genuine ATOP spare/option part. CNC-machined 6061 aluminum transmission case by ATOP, fits front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€139.90*

AT-DBXL029/030/031 ATOP Front- and rear chassis braces, full set, for Losi DBXL 2.0

€109.90*

y0057 Ball & socket tool for Losi and HPI

Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

€17.90*

AT-DBXL021 ATOP Aluminum front transmission mount for Losi DBXL/DBXL-E/2.0 + MTXL

Genuine ATOP spare/option part. Front transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€79.90*

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0

Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces

€34.90*

Details

AT-DBXL 015 ATOP Lower front- and rear alloy a-arms for Losi Desert XL/XL-E / 2.0

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum suspension arms for Losi DBXL. Set of four a-arms with plastic bushings for the hinge pins, all required nuts and bolts are included.Contents:2 pieces

€79.90*

Details

AT-DBXL026 ATOP Aluminum front spindles for all Losi DBXL/MTXL

Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless. Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces

€89.90*