15 products found for "y1428"

rc-car-online - Home

y1528 Bearing puller for differentials

Genuine HT spare/option part. Bearing puller especially for the disassembly of ball bearings from differentials.The arms are reliably fixed at the set distance by an adjustment cone, which makes the use of this puller very easy. The thin hooks allow the use even with little space between ball bearing and differential.Dimensions: Min. opening width: 17 mm Max. opening width: 50 mm Max. height from the Clutch: 25 mmContents:1 piece

€19.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1028 HT Aluminum front bulkhead A for 2WD

Genuine HT spare/option part.With provision to mount a stabilizer bar. Comes with two pairs of special bushings to adjust camber changes during the suspension movement.For a complete bulkhead you need droop stops y1029 (not included)!Fits 1/6 cars like Marder, Monster Models, Pajero, Beetle and many more. Contents:1 piece

€29.90*

y1422 Clamping ring for engine quick mount

Genuine HT spare/option part. Spare part for engine quick mount y1421.

€39.95*

y1468 Tray for small parts with magnetic vinyl

Genuine HT spare/option part. Once again misplaced nut or bolt or, or ... . The tray for small parts with magnetic vinyl brings this to an end!Dimensions: Length: 105 mmWidth: 85 mmdepth: 10 mmContent:1 Piece

€9.90*

y1420 Diff Locker for Losi 5ive-T/2.0, 5ive-B and Mini

Genuine HT spare/option part. The spool replaces the center differential and keeps the speed of both output shafts the same. As a result, especially the acceleration of the vehicle is significantly increased.The spool is nicely made of high-quality burnished steel and very strong. Its total length is the same as a normal differential housing with gasket. The gasket is no longer used with the spool. The driving pin of the front output shaft is secured by an O-ring. The screws for the connection with the spur gear are secured with nylock nuts. This eliminates the need for waiting for the curing of a thread locking compound and makes the removal of screws with damaged head much less critical.The spool would physically fit front and rear applications as well; however, its use here makes no sense to driving dynamics.Scope of delivery:Spool2 x Driving pin 4 x 20 mmO-ring4 x Steel nylock nut M4

€39.90* €59.95* (33.44% saved)

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Configure now

y1428 HT aluminum layshaft spur gear carrier on-road

y1428 Version: y1428/01 Suitable for FG and Smartech touring cars

Fits FG and Smartech touring cars in combination with HT steel spur gear on-road y1427. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The carrier is available in two versions:y1426/01 Suitable for FG and Smartech touring cars (not for EVO 2020)y1426/02 for FG touring cars EVO 2020

€44.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

y1478 pump for re-fueling and de-fueling

The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

y1438 Front section BMW M3 Superstars, clear

y1438 Thickness: y1438/03 - 2,00 mm version+ 4.55EUR

Spare part for y1437 BMW M3 Superstar body shell.Available material thicknesses:1.0 mm2.0 mmPainting tips:

Variants from €32.95*

€34.21*

y1418 Heavy duty bead lock rings for MadMax rims

y1418 Color: y1418/02 - Blu

Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow

€17.90*

y1421 Engine quick mount for G320 Zenoah in FG 1/5 scale

y1421 Versiown: y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³

Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!

€74.95*

y1427 HT steel spur gear on-road with 39, 40, 41 teeth

y1427 Version: y1427/40 HT steel spur gear

Fits FG and Smartech touring cars in combination with HT aluminum layshaft spur gear carrier on-road y1428. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions

€49.90*

y1482 Spring band clamps for tuned pipe connectors, 22 to 34 mm diameter range

y1482 Size / piece: y1482/06-5 Spring band clamps 27 - 29 mm+ 4.5EUR

Genuine HT spare/option part.Spring band clamps are self-clamping and can self-adjust to diameter changes due to temperature variations or properties of the tube material.With this feature of self-adjustment, spring band clams are ideally suited for hose connections between exhaust manifold and tuned pipe with their high temperature load.Unlike worm drive clamps with their relatively large adjustment range, spring band clamps must be selected closely related to their intended application. For this purpose, the outer diameter of the hose in the mounted state must be measured. The clamp, whose nominal diameter corresponds most accurately to the value determined, should be used.In the options menu you can select from sizes ranging from 22 to 34 mm and packs of one or five clamps.Contents:1 piece / 5 pieces

Variants from €0.99*

€5.49*

y1423 Engine flange for engine quick mount, G320 version available for FG 1/5 models

y1423 Version: y1423/01 for all Zenoah and Chung Yang engines up to 30 cm³

Genuine HT spare/option part. For fitment on additional engines or as a spare part for engine quick mount y1421. The engine flange is available in two versions:y1423/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1423/02 for Zenoah G320 - For installation of a Zenoah G320 in a FG Evo (Model range from 2004 till 2014). Fits the standard quick mount.When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1423/01 does not fit in combination with Zenoah OEM clutch!

€39.95*

15 products found for "y1428"

Filter products

rc-car-online - Home