10 products found for "y0711_01"

rc-car-online - Home

y0711/01 Single-sided split alloy servoarm for Savöx SV-0236MG, Rhino and 805er Servo

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft!Suitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€18.90*

y0781/01 Dry-Fluid "Gear Lube" for gears, 10 ml

Dry lubricant instead of oil DryFluid Extreme Gear Lube is specifically designed for highly loaded gears in models. It is characterized by extreme pressure resistance and excellent adhesion. Through the use of solid lubricant components, it shows only a slight tendency for dust and dirt retention. Main applications of the newly developed Gear Lube Gear are of model helicopters, rc-cars and trucks, model trains and servos. Also ideally suited for shafts and gimbals of any kind.DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Especially the long-term effects of DryFluid Extreme will delight any modeler. Product characteristics at a glance: Exciting lubricating propertiesReduces power losses caused by friction Reduces operating noise Reduces wear Extremely pressure resistant Long-term stability Highest adhesion High material compatibility with metals, plastics and rubber materials Low tendency for dust and dirt binding Application Notes: A thin layer of the Gear Lube is enough for an extreme lubricating effect. If possible, apply to an upright standing gear and rotate it during the application. For hard to reach places and selective applications use the included canula. For fine and uniform distribution use a fine hair brush immediately after the application of Gear Lube. Transmissions that have not been treated with Gear Lube before should be thoroughly cleaned first. Shake well before using and apply sparingly!High End dry lubricant for highly loaded gears in models. Especially for transmissions of model helicopters, rc-cars, trucks, model trains and servos. Can also be used for shafts and gimbals of any kind Through the use of dry particles, lubricating polymers and high-end lubricating fluids an unprecedented lubricating effect is achieved. Extremely pressure-resistant and with excellent adhesion. Very low tendency for dust and dirt retention. Multistage dry lubricant system with long-term effects.

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y0701/01 Single-sided split alloy servoarm

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft!Suitable for all servos with an output shaft with 25 tooth spline shaft, for example:y2006 Digital Big-Scale Servo D-21HV Nearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!holes for linkage with 3 mm diameterWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 piece

€18.90*

y0791/01 SPEED TEC EXPERT Zenoah G240 tuning cylinder set

Race ported top end set for Zenoah G240 engine.The SPEED TEC EXPERT genuine Zenoah G260 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intake Piston: Weight reducedSkirt shortenedPiston above and below piston ring tapered and piston dome ground The set includes the following items: Performance-optimized cylinder and piston, piston ring, piston pin, piston pin circlips and cylinder gasket.To achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().

€229.90*

y0711/03 Split Alloy Servo arm for Losi Super Baja Rey / 2.0 and Rock Rey for 15 tooth spline shaft

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M4 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€14.90*

y0716/01 Torx screwdriver spare blades

y0716_01 Size: y0716/T6 - T6

Very high quality Torx screwdriver blades with ¼ hexagon shaft and engraved size indication.Sizes T7 to t25 are usually required for rc-cars.Available sizes:T6, T7, T8, T9, T10, T15, T20, T25

€5.90*

y0711 Double sided split alloy servoarm for Savöx SV-0236MG, Rhino and Hitec 805 servo

Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces

€19.90*

y0716/02 Torx screwdriver unit handle module

Genuine rc-car-online spare/option part. Very high quality Torx screwdriver handle module with rc-car-online logo.Contents:1 piece

€9.90*

y0715 rc-car-online High tech mechanics gloves, nitrile, black

Genuine HT spare/option part. With non-slip surface perfect for delicate work, actually improving dexterity and grip.Available sizes: 8, 9 and 10.Glove size?Size 8 = 21 cm (S - L) circumferenceSize 9 = 24 cm (L - XL) circumferenceSize 10 = 27 cm (XL - XXL) circumferenceMeasure the circumference of your hand without the thumb and at the widest point (above the ankle). The tape measure should embrace the hand loosely.Norm EN388, Lining 100% polyamide.Partially coated with hightech nitrile Fits like a second skinGrips even when wetGood touch sensitivityLiquid-repellentGood resistance against oil and greaseContents:1 pair / 2 pieces3 pairs / 6 pieces

€8.90*

y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.

Item N° y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.Very low weight hard anodized 19T alloy pinion, for use with the stock 48T spur gear on 1/6 scale 2WD off-road cars from Carson/Smartech/Nutech a.s.o.Diameter 31,6 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€27.90*

10 products found for "y0711_01"

Filter products

rc-car-online - Home