TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines
Supplies
9/64 Allen key wrench for the imperial size mounting screw of the carburetor heat sink on Walbro carbs.
Product information "TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines"
Original TopTuning spare/option part.
Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.
Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!
The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.
In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.
Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.
The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..
For installation in FG 4WD cars the rear cross member # 66212 must be modified.
Content:
Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.
Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!
The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.
In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.
Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.
The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..
For installation in FG 4WD cars the rear cross member # 66212 must be modified.
Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu
Content:
- Carburetor heat sink
- 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs)
- 1 x washer 4 mm
Login
Customers also bought
Alloy pedestal to mount the master brake cylinder of the hydraulic brakes FG Magura 2, Mecatech Expert and Mecatech twin piston brake systems on the sloped chassis part of Off-Road Buggies and Monster models.Lieferumfang1x Pedestal for hydraulic brakes2x Countersunk screw with torx 4x12 2x Countersunk screw with torx 4x14
%
Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece
Genuine FG spare/option part. Suitable for all FG 1:5 and 1:6 2WD and 4WD models. Best fitting of ball bearing seat and distance of gear shaft, non-twisting. To mount this gear plate into the models Marder, Beetle, Beetle On-Road, Pajero and Monster the rear brake 7040/01 is needed.Bearing seatsClutch bell: 22 x 6 mmLayshaft: 19 x 7 mmContent:1 piece
For FG 1/6 4WD competition cars only.Not suitable for conversion of an FG Sportline 4WD models since several small parts required for the swap are not included. As an alternative use item no. y0497.Suitable ball bearing for the layshaft: 6036/05 FG bearing set 10x19x7 with grease filling - 2 pcs
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.
Genuine Samba spare/option part. Replacement o-ring for Samba pipes.
Customers also viewed
%
Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.
Selection HT Car Bag:
y0550 HT Car Bag for 1/5 scale cars
y0550 HT Car Bag for 1/5 scale cars (Fits FG, HPI, Mecatech FW01, Smartech/Carson a.s.o.)Fits for all 1/5 models for example: FG-: HPI-; Mecatech FW01-; Carson-; Smartech-; Conrads-; Harm-; RS5-; Lauterbacher a.s.oMade from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.No dirt in the car boot!Dimensions:Length: 95 cmWidth: 50 cmHeight: 30 cmy0551 HT Car Bag for 1/6 scale cars (Fits FG, Smartech/Carson a.s.o.)Fits for all 1/6 models for example: FG Offroad-; Monster/Stadium-; Racetruck-; Carson-; Smartech-; Reely Carbon Fighter; Losi Super Rock Rey, Super Baja Rey, Axial Jeep and any more models. Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure. No dirt in the car boot! Dimensions: Length: 70 cm Width: 50 cm Height: 40 cm y0558 HT Car Bag XXL for LOSI 5ive-T, Mini 5ive WRC and Desert Buggy XL and many moreThe XXL version is especially made for the Losi 5ive-T, Mini 5ive WRC, Desert Buggy XL; Arrma Outcast/Kraton; Axial Honcho, Traxxas X-Max/XRT; UFRC GR1/Big Bully. Of course, other 1/5 and 1/6 large scale cars will fit into this bag as well; however, in this case the XXL bag gives you plenty of room for additional accessories. Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure. No dirt in the car boot! Dimensions: Length: 100 cm Width: 57 cm Height: 39 cm
The FG Sportsline Formula 1 electric convinces not only by its appearance, but rather by its technical achievements. The unique details such as push rods, horizontal oil pressure shock absorbers, double wishbone and much more can be found in almost no other model.The chassis is built on a high-strength 5mm aluminum chassis plate and thus offers extreme stability. Countersunk holes in the chassis plate allow the screws to be flush, ensuring a flat surface under the model. Versatile adjustment options on the front and rear axles allow the model to be perfectly adapted to your own needs. Adjustments such as camber, caster, etc. are no problem whatsoever, even for beginners, and are made via the double a-arms, which provide maximum stability at the rear axle by means of additional track rods. Also the adjustable aluminum oil filled shock absorbers convince on full length and offer maximum performance even on a very difficult underground. The above mentioned push-rod suspension enables play-free power transfer from the suspension to the shock absorbers, which is essential for precise driving.The factory-mounted combination of 980KV motor and 160A MAX6 esc provides performance that is second to none. With a 6S 22.2V (4S 14.8V is also possible) LiPo batteries, the motor reaches a final speed of about 25,000 rpm, leaving a comparable combustion engine far behind. The braking is done by the 980KV motor and is very strong. Within a few meters the model comes from top speed to a standstill. Those who have searched in vain for reverse gear with a combustion engine will find it with the electric version. The operation is very easy, if you press the brake lever once, you hit the brakes. If you press the brake lever twice, you shift into reverse. With the help of a programming card (available separately) you can adjust all ESC values according to your needs. This includes setting options for power, brake force, low-voltage protection and much more. Furthermore, the model has the following technical: Features: 160A MAX6 esc, 6S compatible (4S also possible) 980KV brushless motor Waterproof components Adjustable aluminum oil filled shock absorbers Aluminum levers for the shocks Aerodynamic Lexan body shell 5mm thick aluminum chassis plate Mounting compartment for steering servo Mounting compartment for separate brake servo (for mechanical/hydraulic brakes) Cogged belt drive Side battery mounts for optimal weight distribution Custom CNC machined motor mount Unique double a-arms Push rod suspension Treaded F1 tires Tuning ball drive shafts Dimensions: Length: 960 mm BrWidtheite: 440 mm Height: 230 mm Wheelbase: 620 mm Technical data 980KV brushless motor: Max. Voltage: 33V Max. Current: 130A Max. Speed: 30.000RPM Power in watts: 4250W Rotor poles: 4 No-load current: 2.8A Resistance: 0.0128 Length: 82mm Diameter: 55 / 58mm with fins Weight: 880g Shaft diameter: 8mm Free shaft length: 30mm Weight: 880g Technical data Max6 esc: Continuous current: 160A Peak current: 1050A Battery: 3S - 8S LiPo or 9-24 cells NiMH BEC: 6V/7,2V - 3A/6A Abmessungen:70x56x46,5mm Weight: 240g Note: In our online shop you can also find a detailed 360° illustration, where especially the technology of the FG Formula1 electric chassis can be seen.Note battery mounting:When mounting the l/h side LiPo battery, you must always make sure that it does not rub against the drive pulley. For this purpose, a 5 mm thick piece of foam mat or something similar between battery and battery holder is sufficient to ensure an appropriate distance. For driving you still need: 2 drive batteries incl. charger Battery dimensions maximum: Length 143 mm/5,6 Width 48 mm/1,9 Height 40 mm/1,6 Connector EC8 The RTR equipment (remote control and steering servo!) The body shell comes unpainted! In our online store you can use our store configurator (shopping cart selection / options menu) to add the desired parts, as well as the completely painted body. Formular 1 models in action!
Genuine FG spare/option part.Colour: oliveContents: 5lDimensions total:Height: 260 mmLength: 260 mmWidth: 150 mmThread: Diameter 37 mm x pitch 5 mmContents:1 piece
Genuine GPM spare/option part. Motor mount with cooling fins for Losi Super Baja Rey / Rock Rey made by GPM, machined from high grade 6061-T6 aluminum. It replaces the weaker cast stock version and adds some cooling to the motor.Contents:1 piece
%
Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece