Throttle linkage dedicated to Mecatech FW01 and FG Evolution.Set includes:1 x 1018/01 Throttle linkage Evo 09 / Comp. 071 x 6534/02 Throttle pivot post for 2 mm linkages1 x Screw M3 x 20 mm2 x Nut M3
2012/502 Brake linkage set dedicated to Mecatech FW01 and FG Evolution.Content:1018/01 Throttle linkage Evo 09 / Comp. 071 x 6534/02 Throttle pivot post for 2 mm linkages 1 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/5101 x Screw M3 x 18 mm2 x Nut M3
Steering servo linkage set dedicated to Mecatech FW01Content:1213/11 Steering linkage l./r., M4 x 42 mm1 x 66244, Ball joint 7mm M4, 2 pcs.1 x 1213/10 Steel ball 7 x 6,5 mm, 2 St.2 x Screw M3 x 16 mm2 x Nut M3
Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution.Suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!Content:1 x y0700 Double sided alloy servo horn1 x y0700/01 Single-sided alloy servo horn2 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/510 (one spacer drilled to 3 mm inner diameter)1 x M3 x 30 mm Screw2 x M3 x 12 mm Nut
Ideal power supply for tire warmers! The Powerbase power supply delivers with 13.8 volts the ideal and constant current for tire warmers. A 45 mm cooling fan on the back keeps the Powerbase power supply running cool. Including a slow 4 A / 250v fuse for overload protection. Specifications: Input voltage: 190 - 240 Volts AC Output voltage: 13.8 volts regulated DCOutput connector: 4 mm plug / alligator clips For additional information pleas go to the Technical data tab. Tire warmers can be found under part numbers y1351/01 and y1351/02 or save with the complete set part number y1351/03.Contents:1 piece
Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution.Suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!Content:1 x y0700 Double sided alloy servo horn1 x y0700/01 Single-sided alloy servo horn2 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/510 (one spacer drilled to 3 mm inner diameter)1 x M3 x 30 mm Screw2 x M3 x 12 mm Nut
Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece
Item N° y0700/01 Single-sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
With the Futaba R404SBS, Futaba offers the fastest and most compact receiver for RC cars and boats on the market today! The R404SBS has the ultra-fast signal transmission F-4G (10 channels with telemetry at maximum transmission speed). This makes the model's response even more direct while maintaining maximum transmission reliability!The new F-4G (Futaba 4th Generation System) transmission mode supports the familiar SR mode and has an even higher transmission speed than the previous T-FHSS SR. At the same time, the size of the new F-4G receivers R404SBS / R404SBS-E could be reduced again. To make this possible, the R404SBS-E has a large, upward-pointing antenna to optimize signal reception. Due to the chosen design, the footprint of the receiver remains unchanged.To take full advantage of the speed of Futaba's F-4G SR technology, there are numerous FUTABA SV servos that can also be converted to SR mode. The following servos are currently SR compatible: BLS371SV, BLS471SV, BLS571SV, BLS671SV, BLS671SVi, BLS373SV, S9372SV, S9373SV, HPS CB700, HPS CT700, HPS CB500, HPS CT500.The R404SBS has antenna diversity. The receiver constantly compares which antenna has the better signal and switches to it in a flash. The R404SBS has the second antenna in the housing.S.BUS2 sensors can be connected to the S.BUS2 port. They transmit up to 32 telemetry data sets. The receiver has an integrated telemetry transmitter that transmits the data to the transmitter. This allows the measured values to be displayed or acoustically output at the transmitter.ATTENTION: The receiver supports HV (High Voltage) and can be powered directly from a 2s LiPo battery. Always make sure that the connected servos are also designed for HV! Technical specifications Transmission type: F-4G Frequency range: 2.4 GHz Channels: 4 PWM / 10 S.BUS Transmission power: 100 mW EIRP S.BUS Port: S.BUS2 Voltage range: 3.7-8.4V Dimensions: 25.5 x 20 x 10.6mm Weight: 5.7g Features 4/10 channel F-4G receiver 10 channels of telemetry at maximum transmission speed SR mode compatible Telemetry with S.BUS2 Telemetry with 32 channels S.BUS2 port Hi-Voltage (HV) Antenna diversity
The brushless Big Scale servo is an extremely robust digital servo, with a high performance brushless motor, in absolute premium quality, with a full aluminum case for optimal heat dissipation in the 2-version with elaborate cooling fins, metal gears and equipped with high-quality 30 cm long silicone insulated cable. Where with other high-performance servos you still have to buy an aluminum top or case as third party options, the brushless Big Scale servo already comes with a full metal case, and above all, the aluminum to features special bushings for the intermediate shafts! Of course, the support from a metal top cover guarantees a much longer service life of the complete gearbox, than with a plastic version! Defective gears are known to be the most frequent cause of failure; especially for highly stressed servos in 1/5 and 1/6 cars! The brushless Big Scale servo is also the first choice for 1/8 and 1/10 race cars, where fast reaction times and high steering forces bring up the demand for an extremely fast and reliable servo! Also, servo mounting tab breakage on the servo cover is virtually impossible with the brushless Big Scale servo. Dimensions:Length: 40 mmWidth: 20 mmHeight: 41.4 mmWeight: 72 gramsPerformance:7.4 V6 VHolding torque kg-cm/oz-in30.0/41726,0/361Speed sec./60°0.110.14Accessories included:Three different plastic servo horns / discFour each rubber grommets and guide sleevesMounting screwsNote: Due to the extreme holding power of the brushless Big Scale servo the rubber grommets should always be installed in combination with the guide sleeves. The brushless Big Scale servo comes with accessories in a high quality plastic case with molded insert.We recommend an aluminum servo arm from the selection of the article:Alloy servoarms, for 25 teeth multi-tooth shaft 9,90 EUR
€109.90*
This website uses cookies to ensure the best experience possible. More information...