LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

€11.99*

Prices incl. VAT plus shipping costs

Available

Product number: losilos252020

EAN: 605482565636

Product information "LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL"

Genuine Losi spare/option part.

Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019:

Remove set screw completely
Open bench vise until the pin just fits between the jaws
Position shaft on vice, held by a second person if necessary
Drive pin out with light hammer blows using a pin punch or a suitable comparable tool
If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible.
When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

Contents:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

y1419/02 Sintered steel clutch complete set for Losi 5ive-T/2.0, Mini and Desert Buggy

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch

€49.90*

Details

y0776 NGK Suppression spark plug cap CY / Zenoah G230/240/260/270/290

The use of NGK spark plug caps with noise suppression resistor offers an optimal suppression of RFI in all frequency ranges without negative effects on engine performance.NGK spark plug caps are equipped with a resistor element made of high quality ceramic material. This ensures a constant resistance value with only a slight deviation in overload conditions. Features: Material: phenolic resinType: 90 degreeColor: Black Resistance: 5 kilo ohms RFI suppression: Yes Waterproof: Yes Cable length: Without cable Connection: SAE terminal nut or integrated terminal Features: Compact type; only 31.5 mm high

€12.90*

2012-93 Mecatech Bearing 10x19x5

Genuine Mecatech spare/option part for the FW01.Clutch bearing, sealed on both sides.Content:1 piece

€9.20*

6036/06 FG Ball bearing 10x19x7 mm sealed

Genuine FG spare/option part. Contents:2 pieces

€19.50*

6431 FG Steel pinion 16 teeth

Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

€26.90*

AT-DBXL002/01 ATOP Spacer bushings for camber/steering rods of Losi DBXL and DBXL-E

Genuine ATOP spare/option part. Aluminum spacer bushings for the ball joints on camber and steering rods of Losi DBXL and DBXL-E.Content:8 pieces

€9.80*

Customers also viewed

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0

Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces

€34.90*

Details

LOS253006 Losi Spring Cups/Clips/Shock Ends Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€29.99*