Skip to main content Skip to search Skip to main navigation
+49 2151 820200
Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm
Fast shipping until 1 p.m.

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD

Product information "LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD"

Genuine Losi spare/option part.

Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019:

  • Remove set screw completely
  • Open bench vise until the pin just fits between the jaws
  • Position shaft on vice, held by a second person if necessary
  • Drive pin out with light hammer blows using a pin punch or a suitable comparable tool
  • If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible.
  • When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!


Contents:
  • 1 piece
Responsible company
Horizon Hobby GmbH
Hanskampring 9
22885 Barsbüttel
Germany

Safety information according to GHS
Signalword: Warning

Safety notice

EBPSS101: Warning: Not suitable for children under 3 years old.
CHILDREN14: Not suitable for children under 14. Use only under direct adult supervision.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Skip product gallery

Accessories / Spare parts

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Regular price: €10.99
Skip product gallery

Alternatives

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Regular price: €10.99
Skip product gallery

Customers also bought

%
y0744 Differential Silicone oil / grease, viscosity 15.000 untill 2.000.000, 50 ml
y0744 Differential Silicone oil / grease, viscosity 15.000 untill 2.000.000, 50 ml
y0744 Viscosity: y0744/02 - 30.000

For changing the locking effect of large scale car differentials.Top quality in 50 ml plastic wide-neck bottles.Silicone oil / grease with a viscosity to choose:15.00030.00050.000100.000300.0001.000.0002.000.000Viscosity of silicone oil at various temperatures.

Content: 50 Milliliter (€316.00 / 1000 Milliliter)

Variants from €14.90
Sale price: €15.80 Regular price: €17.80 (11% saved)
LOS256003 Losi Flanged Bushing, Steel, Set Losi DBXL+MTXL 1/5 4WD
LOS256003 Losi Flanged Bushing, Steel, Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

Regular price: €19.99
LOS252134 Losi Center Driveshaft, Front: DBXL 2.0
LOS252134 Losi Center Driveshaft, Front: DBXL 2.0

Genuine Losi spare/option part. Contents:1 piece

Regular price: €39.99
LOS252135 Losi Center Driveshaft, rear: DBXL 2.0
LOS252135 Losi Center Driveshaft, rear: DBXL 2.0

Genuine Losi spare/option part. Contents:1 piece

Regular price: €39.99
Skip product gallery

Customers also viewed

LOS252021 Driveshaft rear center Losi DBXL 1/5 4WD
LOS252021 Driveshaft rear center Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

Regular price: €59.99
LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Regular price: €10.99
6108 FG Pins for driveshaft 4x22mm
6108 FG Pins for driveshaft 4x22mm

Genuine FG spare/option part. Contents:4 pieces

Regular price: €12.90
LOS252056 Losi Dogbone 174 mm, Center, Front, DBXL-E
LOS252056 Losi Dogbone 174 mm, Center, Front, DBXL-E

Genuine Losi spare/option part. Contents:1 piece

Regular price: €19.99
Loading...
Upload in progress, please be patient ...