LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD
€39.99
Available
Product information "LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD"
Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019:
- Remove set screw completely
- Open bench vise until the pin just fits between the jaws
- Position shaft on vice, held by a second person if necessary
- Drive pin out with light hammer blows using a pin punch or a suitable comparable tool
- If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible.
- When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!
Contents:
- 2 pieces
Login
Alternatives
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set
Accessories / Spare parts
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set
Customers also viewed
Genuine Losi spare/option part. Contents:1 piece
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!
Genuine Smartech spare/option part.Total length: 130 mm.Contents:2 pieces
Genuine FG spare/option part.Contents:1 piece
Genuine Losi spare/option part. Also painted available: LOS250010 Painted body shell Losi Desert Buggy XL K&N LOS250016 Body Set, Screened, black, DBXL-E LOS250017 Body Set, Screened, grey, DBXL-EContents:1 setPainting tips:
Genuine Losi spare/option part.
Genuine Top Tuning spare/option part. Beast Edition: Losi XL-E Standard equipment: Beast Edition: Motor: 780kV 520kV Regler: 160 Ampere 300 Ampere S-Leistung: 8S 12S 8S is not enough? You want to go to the limit? Then we have the right thing for you! With the Top Tuning conversion kit it is now possible to mount the ZTW Beast Pro Combo. With the torquey 620KV motor and the 12S 300A esc even the roughest off-road tracks are no problem anymore. The esc is fully programmable using the separately available programming card and can therefore be adapted to all track conditions. In addition, the supplied 15T pinion provides higher gearing and when driving with 12S, top speed is increased by approx. 20%.TT56112/520Top Tuning Monster Brushless Motor 520kV Max. amps: 129 A Max. voltage: 57 V Max. power: 7,350 W KV (RPM/Volt): 520 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG y1549 ZTW Beast Pro 300A 12S ESCSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash-proofContents:1 piece