8453/01 FG Front upright for 1:5 with steel ring

Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces

Genuine FG spare/option part.Reinforced version with steel inlay to prevent the M5 bolts from being pulled out.Bearing seats: 22 x 7 mm.Contents:2 pieces

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 530 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required. Incl. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 780 mmWidth: 392 mmHeight: 240 mmWheelbase: 530 mm

Genuine FG spare/option part. Rigid plastic rear plate. Fits all FG 2WD cars except Evo/Competition and Formula 1.Content:1 Piece

Genuine FG spare/option part. Standard plastic wishbone for all 2WD FG off road models except Leopard race and monster/stadium models with dual shock axles.Contents:1 piece

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

Genuine FG spare/option part. Heavy duty servos 2WD and 4WD 1/5 and 1/6 models. Ball-bearinged with metal gears.Speed: 0.22s-0.20s/60°Torque: 26 - 28kg/cmDimensions : 59,5 x 29,5 x 51,3 mmVoltage: 6.0-7.4VWeight: 154gContents:1 piece