Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Product Safety DangerCauses serious eye irritation.Highly flammable liquid and vapour.May cause drowsiness or dizziness.Repeated exposure may cause skin dryness or cracking.Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters

Genuine FG spare/option part. Screw retention medium for securing and sealing of screws, nuts, bolts a.s.o. Also suitable for galvanized parts. Temperature stability: between -50° to 150°C.Content:1 piece / 35g

Genuine FG spare/option part. Used to lock and seal threads, to retain bearings, bushings etc. and to seal flanges.Temperature stability: between -50° to 150°C.Content:1 piece / 35 ml