Adhesives Thread locking compound Sealing Matterial

y0113 Thread locking compound

kleb_0005 Strength: y0113/02 High+ 2EUR

Genuine HT spare/option part.Available as 272 high strength and heat resistant, 270/1 high strength or 241 medium strength.The strength of 272 and 270/1 is comparable, but 272 can handle temperatures up to 230°C vs. 150°C for 270/1. It is therefore the perfect choice for applications like exhaust or clutch pinion bolts. However, curing of 272 takes at least twice as long as 270/1.An excellent recommendation for removal of screws treated with threadlocking compound:CFH Diamant M50 Gasbrenner, y1007 Contents:1 piece / 10 gram

Content: 10 Gramm (€990.00* / 1000 Gramm)

Variants from €7.90*

€9.90*

y19281 HT Tire adhesive 4000, 1pce.

Item N° y19281 HT-tire adhesive 4000, 1pce.1 piece / 20 grammsHT-tire cement, specially formulated for rubber/plasticContent:20 gr bottle

Content: 20 Gramm (€345.00* / 1000 Gramm)

€6.90*

y0067 HT tire cement and activator

Accelerator-spray is the second component to cure superglue immediately.This set is also particularly suitable for the possible repair of loosened tire/rim gluing!Advantages:Tangible adhesion after a few secondsAromatic solvents and hexane freeSuitable for hobby, craft, industry and householdProcessing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.Contents:Special tire cement ht 4000Spray can activator

Content: 170 Milliliter (€87.65* / 1000 Milliliter)

€14.90*

y0994 Marston heat-proof sealer - 1pce.

Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Content: 80 Milliliter (€123.75* / 1000 Milliliter)

€9.90*

y0565 RC-Tech Flexa Fix body shell glue

Genuine HT spare/option part. For all epoxy models, plastic and polycarbonate/lexan body repairs!Direction of use:Use a brush or other applicator. Apply enough Flexa Fix to the damaged area. Be careful not to apply too much in one go as it can be difficult to manipulate. If necessary apply two or three coats to build up the joint area. Use epoxy blanket of pieces of polycarbonate (Lexan) to re-enforce if necessary.You can also use the Flexa Fix to re-enforce the body corners (let the pure product leak into the corners) or to make flexible battery packs.Contents:1 piece / 100 ml

Content: 100 Milliliter (€109.00* / 1000 Milliliter)

€10.90*

y0743 Clutch-Safe 10 g, adhesive especially for clutch pads

Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube

Content: 10 Gramm (€495.00* / 1000 Gramm)

€4.95*

y804 HT-flange sealer 518, 50 ml up to 200°C

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Content: 50 Milliliter (€538.00* / 1000 Milliliter)

€26.90*

y0807 MD-Sil RTV silicone sealer

Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml

Content: 80 Milliliter (€211.25* / 1000 Milliliter)

€16.90*

y19015 Bindulin Dichtfix (untill 180°!)

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

Content: 45 Gramm (€331.11* / 1000 Gramm)

€14.90*

y0285 Accelerator - 1pce.

Item N° y0285 Accelerator - 1pce.For all tire adhesives above,150 ml spray canAccelerator-spray is the second component to cure superglue immediately.Advantages:Tangible adhesion after a few seconds Aromatic solvents and hexane free Suitable for hobby, craft, industry and household. Processing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.

Content: 150 Milliliter (€66.00* / 1000 Milliliter)

€9.90*

y1360 MD Two-component glue CA-STAR 2K met

Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

6503 FG Thread locking compound, high strength

Genuine FG spare/option part. Screw retention medium for securing and sealing of screws, nuts, bolts a.s.o. Also suitable for galvanized parts. Temperature stability: between -50° to 150°C.Content:1 piece / 35g

Content: 35 Gramm (€957.14* / 1000 Gramm)

€33.50*

STT124 Speed-Tec sealing agent, small tube

Original Speed-Tec Ersatz-/Tuningteil.Sufficient for sealing of two enginesSealing compound for sealing engines Special elastic silicone based sealant li> Temperature resistance. -50° C to +250° C For sealing cylinder, insulator, carburetor, crank case Contents: Tube with 8 grams

€3.25*

This product is no longer available.

6506 FG 4 in 1 securing device

Genuine FG spare/option part. Used to lock and seal threads, to retain bearings, bushings etc. and to seal flanges.Temperature stability: between -50° to 150°C.Content:1 piece / 35 ml

Content: 35 Milliliter (€814.29* / 1000 Milliliter)

€28.50*

y1358 PTFE thread sealing tape, 12 mm wide, 10 m roll

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters

€2.90*

y0115 Accellerator - 1pce.

For all tire adhesives above,15 ml pump spray bottleAccelerator-spray is the second component to cure superglue immediately.Advantages: Tangible adhesion after a few seconds Aromatic solvents and hexane free Suitable for hobby, craft, industry and household.Processing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.

Content: 15 Milliliter (€593.33* / 1000 Milliliter)

€8.90*

Z159 HPI Thread lock

Genuine HPI spare/option part. An excellent recommendation for removal of screws treated with threadlocking compound: y1007 CFH Diamant M50 Gasbrenner<Contents:1 piece / 3 ml

Content: 3 Milliliter (€1,826.67* / 1000 Milliliter)

€5.48*

This product is no longer available.