y1004 Driveshaft boots for ball drive + dogbones
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces
y1218 Springs for drive shafts
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
y1036 HT rose joints with conical spacers
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
y0578, Alloy front shock tower for FG Sportsline and Off-Road 4WD, 1 pce.
Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.
y1309 All steel linkage for steering servo/servo saver application
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
y1037 HT Aluminum brake cable bracket
Genuine HT spare/option part.For secure installation of the brake cables.Contents:1x Brake cable bracket2x Socket head cap screws 3 x 25 mm2x Self-locking hexagon nut M3
y0673 Carbon fastening strip for FG no. 8418 - 2 pcs.
Use instead of plastic fastening strip FG # 8418/07 (for FG front bumper # 8418).Dimensions:Width: 95,7 mmHeight: 16,8 mmDistance between holes: 75 mmBore diameter: 8 mmThickness: 2 mm
y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars
Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!
y0932 HT Alloy front uprights for FG / Smartech
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
y68413/01 Front alloy uprights 2WD/4WD, touring car 530/535
Genuine HT spare/option part.The set includes uprights, steering arm, alloy stoppers, screws.Suitable for touring cars, 530/535 mm weelbaseContents:1 set For older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.https://rc-car-online.de/en-ersatzteile_main,15.html
y0722 Axle plugs for Losi 5ive-T/2.0, Mini
For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.
6496 FG Alloy front bulkhead 2WD A and B
Genuine FG spare/option part.CNC-manufactured front axle mounts A and B in alloy with rebound stop. The borings for the wishbone pins are equipped with guide bushes. Suitable for Marder, Marder Race, Beetle On-/Off-Road and Monster models.Contents:1 set
66266, FG Alloy a-arm, front upper 4WD, 1 pce.
Alternative: y2002 Alloy a-arm, front upper FG 4WD - Fits FG Leopard 4WD und Sportsline onroad 4WD with 510mm wheelbase.Does not fit FG Leopard 2WD und Sportsline onroad 4WD with 530mm wheelbase.
66275/05 FG Front cardan shaft 4WD
Genuine FG spare/option part.Contents:1 piece
y0264 C-clips with handle 4 - 6 mm
Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces
Elcon 14404, front shock tower for FG Monster Truck 2WD
CNC-milled aluminum version, suitable for the old version of the FG 2WD monster and stadium models. These vehicles were distinguished by coming from the factory with four shocks each front and rear. The shock tower comes complete with mounting hardware and four quick-release mounts for the upper shock ends.
66270/03, FG Plastic steering stop for 2WD/4WD, 2 pcs.
Genuine FG spare/option part. Measures:Length: 40mmDiameter: 10 mmFor older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.
y0350 Offroad tuning spring Dirt-Spring for GD
Genuine HT spare/option part. Fits Carson Gas Devil/ Hell Devil 4x4. Not for Thunderbolt!.Measures:Inna diameter: 31,4 mmOuter diameter: 37 mmLength short spring: 103 mmCoils short spring: 8 StückLength long spring: 143 mmCoils long spring: 10 StückFront axle:VersionMeasuresColorItem N°GD012.3 x 103 mmyellowy0350/01GD022.4 x 103 mmredy0350/02GD032.6 x 103 mmbrowny0350/03GD042.75 x 103 mmbluey0350/04GD052.8 x 103 mmsilvery0350/05GD062.9 x 103 mmblacky0350/06Rear axle::VersionMeasuresColorItem N°GD072.3 x 143 mmyellowy0350/07GD082.4 x 143 mmredy0350/08GD092.6 x 143 mmbrowny0350/09GD102.75 x 143 mmbluey0350/10GD112.8 x 143 mmsilvery0350/11GD122.9 x 143 mmblacky0350/12HelpThe stock springs have 2.5 mm wire diameter. The Gas Devil / Titan shocks are factiry filled with silicone oil 500, which is slightly soft in rear and way to soft in front. In rear brown springs with oil in the 800 - 900 range or blue springs with 900 - 1000 range oil should be fine for bashing. In front blue springs and 1500 silicone oil are a good point to start from. Due to the size of the shocks you need two bottles of oil pes axle.Contents:2 pieces
68420/06 FG Alum. servo saver 80°, 1:5 4WD, complete
Genuine FG spare/option part. In details improved aluminium servo saver. Improvement through modification of the slant to 80° for the protective function. According to the regulating power and the number of steering servos the red and blue FG servo saver springs can be assembled. Only suitable for 4WD 1/5 scale.Contents:1 piece
y1032 HT Aluminum shock tower Marder 2WD
Genuine HT spare/option part.Fits Marder, Beetle, Pajero and Monster Beetle,Material thickness:6 mmContents:1 piece