Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake.Compatible with the DOT4/DOT5brake fluid.Contents:1 piece

Replacement part for Mecatech twin piston hydraulic brake.

Genuine Mecatech spare/option part. Dimensions:Inner diameter: 2 mmOuter diameter: 4 mmContents:1 piece

Replacement part for Mecatech Expert and Cross Hydro.Inner diameter of eylet and cap: 4 mmLength: 21 mm

Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake.Contents:1 piece / 50 ml

Replacement part for Mecatech twin piston hydraulic brake.

Cable: 305 mmSheath: 220 mmSpare part for , , , , and .

Genuine FG spare/option part. Spare part 9440.

Dimensions:Inner diameter: 2 mmOuter diameter: 4 mmContents:1 piece

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake.Contents:1 piece / 50ml

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

connector straight for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake.Compatible with the DOT-4 brake fluid.Contents:4 pieces

Genuine FG spare/option part. Contents:1 piece

Length 12 mmInner diameter 3.3 mmWire diameter 0.3 mmSpare part for , , , , , , , , , , and .

hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Length: 1 meterDimensions:Inner diameter: 2 mmOuter diameter: 4 mm

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Alloy pedestal to mount the master brake cylinder of the hydraulic brakes FG Magura 2, Mecatech Expert and Mecatech twin piston brake systems on the sloped chassis part of Off-Road Buggies and Monster models.Lieferumfang1x Pedestal for hydraulic brakes2x Countersunk screw with torx 4x12 2x Countersunk screw with torx 4x14

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

Angle connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

Cable: 350 mmSheath: 270 mmSpare part for , , , , and .

Top quality epoxy P-R-M Race brake discs with 10 dirt slots for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)! The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218). The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.1 pair (2 pieces) Dimensions: Outer diameter: 60 mm Thickness: 2 mmsocket for 18 mm square wheel drive

Replacement part for Mecatech twin piston hydraulic brake.