ST-AN26V SPEED TEC 0,25/0.50 mm carburetor AN - expansion sealing gasket

Genuine Speed-Tec spare/option part. For Zenoah G230/G240/G260/G270/G290AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Item N° 08610/01 Front axle with collar, 1pce.Suitable for all FG front uprights. Suitable for square wheel driver 9,5mm and 14mm. Dimensions: Shaft: 8 mm Outside thread: M6 Inside thread: M4 Total length: 58 mm

Genuine FG spare/option part.For all Zenoah / CY / Fuelie / PT engines.Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:2 pieces

Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

With a fresh design and innovative tread patterns for even higher performance. We are thrilled to present the 1:5 Supreme V4 – our revolutionary tire for the world of four-wheeled modeling. The new V4 aims to raise the bar in competitions and cater to the needs of drivers. It features a redesigned tread with new patterns meticulously crafted for enhanced performance.  Let’s see its key features: Exceptional Grip: Advanced tread patterns for unparalleled traction on various asphalt conditions. Simplified Driving: Superior control for a smoother and more effective driving experience. Enhanced Durability: Thanks to the new tread design, the tire’s performance remains consistent even in longer sessions. Available in Three Different Compounds.  Like all our products, the V4 is available in various compounds to accommodate different asphalt conditions: - Q01 – SuperSoft - Q03 – Soft - Q05 – MediumNote:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability.Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Dimension:Outside diameter: approx. 116 mmWidth: approx. 65 mmRims: 18 mm square driveContents:2 piece