ST-AN21D SPEED TEC 0,25 mm EWP207 Silencer gasket for CY / Zenoah AN - expansion sealing gasket

€3.50*

Available

Product number: st_an21d

EAN: 4058575120766

Product information "ST-AN21D SPEED TEC 0,25 mm EWP207 Silencer gasket for CY / Zenoah AN - expansion sealing gasket"

Genuine Speed-Tec spare/option part.
For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PT / Losi / Carson
AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels!

The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly!

The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine!

Technical data of the material in contact with fuel:
- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;
- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

y0702 Copper-Exhaust gasket for Zenoah, CY, Fuelie, PT, etc.

Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€4.90*

y804 HT-flange sealer 518, 50 ml up to 200°C

Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Content: 50 Milliliter (€538.00* / 1000 Milliliter)

€26.90*

y19015 Bindulin Dichtfix (untill 180°!)

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

Content: 45 Gramm (€331.11* / 1000 Gramm)

€14.90*

y0994 Marston heat-proof sealer - 1pce.

Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Content: 80 Milliliter (€123.75* / 1000 Milliliter)

€9.90*

y0807 MD-Sil RTV silicone sealer

Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml

Content: 80 Milliliter (€211.25* / 1000 Milliliter)

€16.90*

Similar products

7337 FG Carburetor gasket for CY / Zenoah / Fuelie

Genuine FG spare/option part.For Zenoah G230/G240/G260/G270/G290/G320Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€5.90*

7335 FG Insulator gasket for Zenoah / CY / Fuelie

Genuine FG spare/option part.For Zenoah G230/G240/G260/G270/G290Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€4.30*

7332 FG Silencer gasket for CY / Zenoah / Fuelie / PT

Genuine FG spare/option part.For all Zenoah / CY / Fuelie / PT engines.Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:2 pieces

€4.90*

7373 FG Pump for CY / Zenoah

Genuine FG spare/option part.Contents:1 piece

€9.90*

7313/01 FG Key for Crankshaft for CY / Zenoah / Fuelie

Genuine FG spare/option part. Contents:1 piece

€3.70*

7309/09 FG Piston ring for Zenoah G230/04

Genuine FG spare/option part.Width 0.8 mm.Hint for installation: The green dot on the ring goes towards the clutch side!Contents:1 piece

€15.30*

y1419/01 Clutch spring 6.000 1 / min for the Sintered clutch for Zenoah, Chung Yang, Losi, HPI & Co.

Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece

€5.90*

7357 FG Air filter foam for CY / Zenoah / Fuelie

Genuine FG spare/option part.Contents:2 pieces

€8.50*

6061 Mielke pull starter with hybrid starter function

Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

y7343/08 Champion Spark plug for Zenoah/CY and other

Genuine Champion spare/option part.The Champion spark plug means higher speed range, longer time of exposure andimproved starting function. Thread size M10 x 1 fits CY / Fuelie / PT / Zenoah G230/240/260/270/290 and otherSerienkerze vom Zenoah G230/240/260/270.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:1 piece

€9.90*

7340/09 FG Rubber cap for kill switch

Genuine FG spare/option part.Protects the switch against dirt and splashes. Highly recommended for off-road use.Contents:1 piece

€3.90*

7316 FG Clutch blocks for Zenoah

Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€19.90*

Customers also viewed

ST-AN25I SPEED TEC 0,25/0.50 mm insulator AN - expansion sealing gasket

st_an25i Thickness: ST-AN25I/050 - 0,50 mm

Genuine Speed-Tec spare/option part. For Zenoah G230/G240/G260/G270/G290AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

€4.40*

ST-AN22 SPEED TEC AN - Expansion sealing gasket for ‚cylinder with two bolt 0,25mm

Genuine Speed-Tec spare/option part. For Zenoah G230/G260AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is e.g. possible to make up for irregularities in the sealed surfaces (e.g. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

€4.40*

y1320 Narrow-Grip 616 type drift tires, mounted and with 24 mm hex for Losi, HPI, MCD

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. Both are available as an option from our shopping cart menu. Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

€99.80*

y1082 Stop collar 2 mm

Genuine HT spare/option part. Necessary for all throttle and brake linkages.Dimensions:Outer diameter: 7 mmWidth: 5 mmContents:5 pieces

€3.45*

y1312 Twin hose bracket

Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Details